Author Topic: My New Project  (Read 64840 times)

0 Members and 1 Guest are viewing this topic.

mx250

  • Guest
Re: My New Project
« Reply #180 on: March 24, 2008, 07:35:40 pm »
...but my main concern now is the amount of smoke it blows..its blowing out everywhere....
Put it into first gear, take off and nail it in every gear. If it still smoking after fifth gear you have a problem :-\ (probably c/c seals). If it clears it was just accumulated oil from standing ;).

I fit seizes in between it wasn't my idea, right?  ;D

Offline VMX Andrew

  • Legend
  • *****
  • Posts: 961
    • View Profile
Re: My New Project
« Reply #181 on: March 24, 2008, 08:23:59 pm »
it has been sitting for something like 6-8months...it wouldnt be the crankseals....the whole motor was rebuilt top and bottom only about 12 months ago.... :) 

Offline DJRacing

  • Legend
  • *****
  • Posts: 1598
  • YZ125X
    • View Profile
Re: My New Project
« Reply #182 on: March 24, 2008, 08:40:25 pm »
Andrew, its been a long time since I have looked at the carb on my YZ250H so I am not sure what it is running.
Is this the first run since the rebuild? If it is then be thankful that it is smokey, at least the bearings have oil on them.
As for crank seals, they can go at any time.
If at first you dont succeed, give up and drink beer

Offline VMX Andrew

  • Legend
  • *****
  • Posts: 961
    • View Profile
Re: My New Project
« Reply #183 on: March 24, 2008, 08:49:24 pm »
this would probably be its 3rd run since its rebuild...yes ive been a bit slack with takin her for a run every so often to keep the seals fresh but i didnt think they would perish that quick...

mx250

  • Guest
Re: My New Project
« Reply #184 on: March 25, 2008, 06:02:35 am »
but i didnt think they would perish that quick...
They don't 'perish' they harden, and I doubt they would need replacing after 6-8 months. Slight damage of the lip may have been done during assembly but most probably just accumulated oil.

Take it for a thrash ;), and report back 8).

Offline DJRacing

  • Legend
  • *****
  • Posts: 1598
  • YZ125X
    • View Profile
Re: My New Project
« Reply #185 on: March 25, 2008, 05:24:45 pm »
Yeah I agree MX250, a good thrashing once it is warmed up. The oil should burn up nicely after sitting around waiting to be taken to heaven and back, yep a good old fashion flogging is what is needed.  ;D
If at first you dont succeed, give up and drink beer

TM BILL

  • Guest
Re: My New Project
« Reply #186 on: March 25, 2008, 06:48:59 pm »

A good old fashioned flogging  ;D
OOps  :-[
« Last Edit: March 25, 2008, 06:52:10 pm by TM BILL »

Offline DJRacing

  • Legend
  • *****
  • Posts: 1598
  • YZ125X
    • View Profile
Re: My New Project
« Reply #187 on: March 25, 2008, 07:24:35 pm »
OOps, My wrench said the piston looked like some overwieght pom was giving it a flogging ;) the only way to keep up with those big brit bangers on a 125, lean her out, keep her pinned and hope for the best. The barrel is in getting a hone and the piston/rings are on the way for the rescue.

Never let a pom pass by.... ;)   ;D   ;D
If at first you dont succeed, give up and drink beer

Offline Freakshow

  • Superstar
  • ******
  • Posts: 7277
  • Adelaide, SA - looking for a "YZA" tank
    • View Profile
Re: My New Project
« Reply #188 on: April 11, 2008, 12:05:47 pm »
Dj,

HOw about slipping it into a champion frame for a bit of track work ?
74 Yamaha YZ's - 75 Yamaha YZ's
74 Yamaha  flattracker's
70  Jawa 2 valve speedway's

For sale -  PRE 75 Yamaha MX stuff, frame, motors and parts also some YAM DT1,2,A and Suzi TS bikes and stuff

Offline VMX247

  • Megastar
  • *******
  • Posts: 8766
  • Western Australia
    • View Profile
Re: My New Project
« Reply #189 on: June 19, 2011, 01:32:51 pm »
Always a good read this thread  8)
Best is in the West !!

Offline Iain Cameron

  • Legend
  • *****
  • Posts: 2015
    • View Profile
Re: My New Project
« Reply #190 on: June 19, 2011, 10:19:18 pm »
Just read this thread DJ magic work mmm must get out to the shed (showed post to my girlfriend also a karen she said something about joining venna boys choir if I even tried to bring a bike inside) Iainyz
Yamaha tragic ; dt1, rt1, dt2, rt2, dt2mx , rt2mx , mx250, mx360,sc500, 74dt125, yzx125, yzc250, yzc400, yzd250, yzd400, yzh250, yzh80 , dt100 , xr75 ko xr80 03 , it175 82 . Not a member of any club

mainline

  • Guest
Re: My New Project
« Reply #191 on: June 27, 2013, 06:19:13 pm »
Thought i'd revive this for relative newcomers to have a squiz. Probably still my favourite resto thread.

Offline Paul552

  • Legend
  • *****
  • Posts: 672
  • HEAVEN #552
    • View Profile
Re: My New Project
« Reply #192 on: June 27, 2013, 09:04:29 pm »
Thought i'd revive this for relative newcomers to have a squiz. Probably still my favourite resto thread.

Thanks great read
'77 YZ125D '84 CR250RE '89 CR250RK '84 CR80RE  '09 YZ250F

Offline YZ250H

  • Legend
  • *****
  • Posts: 2116
  • Back in QLD Baby !
    • View Profile
Re: My New Project
« Reply #193 on: June 28, 2013, 09:22:23 am »
A cool little bike  8) and a top Resto
DJ even let me have a ride on it.  Sweet  ;D
Looking for YZ250C parts NOS if possible

"My inability to use emoticins in the right context is really getting me down :)
The only triple jumps he would have been doing are the hop, skip & jump.

Offline DJRacing

  • Legend
  • *****
  • Posts: 1598
  • YZ125X
    • View Profile
Re: My New Project
« Reply #194 on: July 05, 2013, 08:12:53 pm »
Yea I miss that little bike, it even had a sense of humour, albeit in a gangster kind of way.

 "If you don't start singing now I'll break your f...kin leg"
Roxanne  you don't have to put on the red light   ;)  sorry Bill  ;D

In its own way I think it had  'short-bike syndrome'  because it liked to take on bigger bikes in a do or die fashion.

And like a true gangster hitman/bodyguard it looked after its owner and gave him 3 wins in a row to become "The Don"
 ;D   ;D



If at first you dont succeed, give up and drink beer