« previous next »
Pages: 1 [2] 3  All   Go Down

Author Topic: Tool Of The Week  (Read 6145 times)

0 Members and 1 Guest are viewing this topic.

Offline YZ250H

  • Legend
  • *****
  • Posts: 2116
  • Back in QLD Baby !
    • View Profile
Re: Tool Of The Week
« Reply #15 on: July 02, 2011, 06:59:53 pm »
Not sure stew - been doing some research in the meantime and that kit looks like to go.  Some pretty expensive ones out there, but found on on eBay for $130.  Probably worth that in swearing and angst  ;D ;D
Logged
Looking for YZ250C parts NOS if possible

"My inability to use emoticins in the right context is really getting me down :)
Quote from: GMC on May 03, 2014, 10:35:22 am
The only triple jumps he would have been doing are the hop, skip & jump.

Offline frostype400

  • Legend
  • *****
  • Posts: 2496
    • View Profile
Re: Tool Of The Week
« Reply #16 on: July 02, 2011, 07:04:47 pm »
Where did you get that one Stewart I had one stuck in way to hard last week and I had to weld a bolt to it to tap it out from the other side I need a kit like that. ;)
Logged
1971 tm400 and PE's

Offline Canam370

  • Legend
  • *****
  • Posts: 1608
    • View Profile
Re: Tool Of The Week
« Reply #17 on: July 02, 2011, 07:27:43 pm »
These kits can be sourced locally through MCS via your favourite bike shop. I have a set at the shop and they work well and have proven to be robust.
« Last Edit: July 02, 2011, 07:32:07 pm by Canam370 »
Logged
WANTED. Canams;all models,complete or parts.SWM stuff too!

I'm THE Thread Killer - when I post a thread dies!

Offline YZ250H

  • Legend
  • *****
  • Posts: 2116
  • Back in QLD Baby !
    • View Profile
Re: Tool Of The Week
« Reply #18 on: July 02, 2011, 07:37:15 pm »
How much are they Can am ??
Logged
Looking for YZ250C parts NOS if possible

"My inability to use emoticins in the right context is really getting me down :)
Quote from: GMC on May 03, 2014, 10:35:22 am
The only triple jumps he would have been doing are the hop, skip & jump.

oldfart

  • Guest
Re: Tool Of The Week
« Reply #19 on: July 02, 2011, 07:41:28 pm »
I bought it out of shear frustration a few years ago From  BSC  bearings.

Frosty,  she is a Toledo brand Kit # 246300   Puller sizes  8-10- 12-15-17 -20 -25-30

12-15 & 17 are the most frequently used out of my kit pulling Pe motors apart  ;)of which # 17 pulls that pesky bearing next to clutch actuator shaft.  
Logged

Offline frostype400

  • Legend
  • *****
  • Posts: 2496
    • View Profile
Re: Tool Of The Week
« Reply #20 on: July 02, 2011, 08:22:35 pm »
Thanks Stewart, bought a Toledo set and a book on bathurst gtho falcons, thanks Michael. ;)
Logged
1971 tm400 and PE's

Offline LWC82PE

  • Superstar
  • ******
  • Posts: 6006
    • View Profile
    • PE motorcycles & SuzukiTS.com
Re: Tool Of The Week
« Reply #21 on: July 02, 2011, 08:40:47 pm »
You can get the MCS stuff here http://www.mcsonline.com.au/ well you can see it here but you need to get it from a dealer. I have a fair few of their workshop tools. The right handle screwdriver is very handy.
Logged
Wanted - 1978 TS185 frame or frame&motor. Frame # TS1852-24007 up to TS1852-39022

Offline Canam370

  • Legend
  • *****
  • Posts: 1608
    • View Profile
Re: Tool Of The Week
« Reply #22 on: July 02, 2011, 09:14:00 pm »
Quote from: YZ250H on July 02, 2011, 07:37:15 pm
How much are they Can am ??

Will have to check Monday.
Logged
WANTED. Canams;all models,complete or parts.SWM stuff too!

I'm THE Thread Killer - when I post a thread dies!

Offline YZ250H

  • Legend
  • *****
  • Posts: 2116
  • Back in QLD Baby !
    • View Profile
Re: Tool Of The Week
« Reply #23 on: July 02, 2011, 09:46:47 pm »
That would be good thanks.  Otherwise it's eBay  ;)
Logged
Looking for YZ250C parts NOS if possible

"My inability to use emoticins in the right context is really getting me down :)
Quote from: GMC on May 03, 2014, 10:35:22 am
The only triple jumps he would have been doing are the hop, skip & jump.

Offline mick25

  • Legend
  • *****
  • Posts: 1162
  • Hunter valley NSW
    • View Profile
Re: Tool Of The Week
« Reply #24 on: July 03, 2011, 06:10:12 am »
Ballards sell them to ,I got one a couple years back ,good tool saves the nuckles
Logged

mainline

  • Guest
Re: Tool Of The Week
« Reply #25 on: July 03, 2011, 08:58:58 am »
go the Toledo brand if you can, they're worth it. I think I paid $130 or similar for the same kit as Stu posted up. Shop around though the other local bearing shop was $70 more expensive
Logged

Offline YZ250H

  • Legend
  • *****
  • Posts: 2116
  • Back in QLD Baby !
    • View Profile
Re: Tool Of The Week
« Reply #26 on: July 03, 2011, 10:17:14 am »
Logged
Looking for YZ250C parts NOS if possible

"My inability to use emoticins in the right context is really getting me down :)
Quote from: GMC on May 03, 2014, 10:35:22 am
The only triple jumps he would have been doing are the hop, skip & jump.

Offline yamaico

  • Legend
  • *****
  • Posts: 816
    • View Profile
Re: Calling Mainline
« Reply #27 on: July 03, 2011, 11:08:34 am »
Quote from: YZ250H on July 02, 2011, 05:31:19 pm
What is this mysterious tool :-\.  The picture is long gone.  Want to post up a picture of yours ??
Having a few "issues"  ::) with the blind bearings in the 125 gearbox.  Before you come back with some smart arse reply they are the ones you can't get behind to knock 'em out  ;)
Others also welcome to chime in  ;D ;D
Warm your cases in the oven - the bearings will fall out.
Logged

Offline YZ250H

  • Legend
  • *****
  • Posts: 2116
  • Back in QLD Baby !
    • View Profile
Re: Tool Of The Week
« Reply #28 on: July 03, 2011, 11:31:36 am »
Tried that.  it no workies  :-\  All the others came out easily with a gentle tap, the blind ones not so.
Logged
Looking for YZ250C parts NOS if possible

"My inability to use emoticins in the right context is really getting me down :)
Quote from: GMC on May 03, 2014, 10:35:22 am
The only triple jumps he would have been doing are the hop, skip & jump.

Offline Mike52

  • Legend
  • *****
  • Posts: 1834
  • 81 KTM 125 LC
    • View Profile
Re: Tool Of The Week
« Reply #29 on: July 03, 2011, 12:58:27 pm »
Bloke came into the hire shop last week wanting to hire a pantek.
He complained when told that the first 100k was free then 30 cents a k .
Said he was told that it was $30 a hundred k. ::)
Then he wanted to know how much fuel he would use driving to where he was going and back. ???
He,s gotta make TOOL of the week easy.

If I appear insane then I rekon I have a gooood reason. :)
Logged
85/400WR,86/240WR,72/DKW125,Pe250c,TC90,TS100,XT250,86/SRX250,XR400r
Friend  struggling up a hill on a old bike at MTMee .http://www.youtube.com/watch?v=cjj6E2MP9xU.
Pages: 1 [2] 3  All   Go Up
« previous next »