« previous next »
Pages: [1]   Go Down

Author Topic: Info on new CR480 rod kit  (Read 5404 times)

0 Members and 1 Guest are viewing this topic.

Offline mick25

  • Legend
  • *****
  • Posts: 1162
  • Hunter valley NSW
    • View Profile
Info on new CR480 rod kit
« on: July 15, 2013, 06:00:33 pm »
A mate of mine is chasing a new rod kit for a 83 CR480 , any info where to get one will be tops.
I don't know if the 82 CR480 is the same or even the 84 CR500.
someone with a Honda zedder disc may know.
Thanks mick
Logged

Offline evo550

  • Legend
  • *****
  • Posts: 2435
    • View Profile
Re: Info on new CR480 rod kit
« Reply #1 on: July 15, 2013, 09:40:13 pm »
Me thinks 82 and 83 same...NLA, 84 500 available but longer, by about 12mm I think.
I have been down the road of fitting a 84 rod to an 82 with spacer under bottom of cylinder, only to find exhaust port was raised to high and was half blocked off by frame main front down tube. I should have taken $750 out into the back yard and burnt it, would have saved me two months of flucking as I ended up reusing the old rod....
Logged

Offline Lozza

  • Legend
  • *****
  • Posts: 4206
    • View Profile
Re: Info on new CR480 rod kit
« Reply #2 on: July 15, 2013, 11:20:21 pm »
Could have found a piston with a lower comp height  ;)
Logged
Jesus only loves two strokes

Offline GMC

  • Legend
  • *****
  • Posts: 3693
  • Broadford, Vic
    • View Profile
Re: Info on new CR480 rod kit
« Reply #3 on: July 16, 2013, 09:45:26 am »
Would there not be something that is closer than 12mm longer out there?

Part # = 13201-KA5-770
Part Description = ROD, CONNECTING
Model Count = 2
CR480R-C 1982 480 CR480R Off Road
CR480R-D 1983 480 CR480R Off Road
Logged
G.M.C.  Bringing the past into the future

Shock horror, its here at last...
www.geoffmorrisconcepts.com

For the latest in GMC news...
http://www.geoffmorrisconcepts.com/8/news/

Offline evo550

  • Legend
  • *****
  • Posts: 2435
    • View Profile
Re: Info on new CR480 rod kit
« Reply #4 on: July 17, 2013, 01:53:44 pm »
Quote from: Lozza on July 15, 2013, 11:20:21 pm
Could have found a piston with a lower comp height  ;)
....now ya bloody tell me...
Logged

Offline mick25

  • Legend
  • *****
  • Posts: 1162
  • Hunter valley NSW
    • View Profile
Re: Info on new CR480 rod kit
« Reply #5 on: July 17, 2013, 08:41:43 pm »
Thanks for the info so far guys ;) hes trying a bloke in the uk for one fingers crossed.
Logged

Offline Matador107

  • B-Grade
  • ***
  • Posts: 235
    • View Profile
Re: Info on new CR480 rod kit
« Reply #6 on: July 17, 2013, 09:14:32 pm »
Have a look at this bloke in the UK. He is an agent for Italkit and I know he will sell to Aust because I enquiried some time ago. Kevin Breedon Racing.
Martin
Logged
Bultaco Metralla, Matador MK 5, Montadero mk2, El Bandido model 18,plus lots of bits and two Honda XR's 250,350.

Offline Matador107

  • B-Grade
  • ***
  • Posts: 235
    • View Profile
Re: Info on new CR480 rod kit
« Reply #7 on: July 17, 2013, 09:51:08 pm »
This bloke as well apparently he manufactures. Phil Denton Engineering in England.Hope it all helps.
Logged
Bultaco Metralla, Matador MK 5, Montadero mk2, El Bandido model 18,plus lots of bits and two Honda XR's 250,350.

Offline Lozza

  • Legend
  • *****
  • Posts: 4206
    • View Profile
Re: Info on new CR480 rod kit
« Reply #8 on: July 18, 2013, 12:22:16 pm »
Quote from: evo550 on July 17, 2013, 01:53:44 pm
Quote from: Lozza on July 15, 2013, 11:20:21 pm
Could have found a piston with a lower comp height  ;)
....now ya bloody tell me...
You never asked ;D
Logged
Jesus only loves two strokes

Montynut

  • Guest
Re: Info on new CR480 rod kit
« Reply #9 on: July 18, 2013, 02:53:12 pm »
Quote from: Matador107 on July 17, 2013, 09:14:32 pm
Have a look at this bloke in the UK. He is an agent for Italkit and I know he will sell to Aust because I enquiried some time ago. Kevin Breedon Racing.
Martin
Kevin is great good guy and will go out of his way to help as he is a vintage racer himself. He has raced CRR & VMX on Bultaco for many years. He has contacts with Italkit and has obtained parts from them in a few days for me in the past. Highly recommended.
Logged

Offline mick25

  • Legend
  • *****
  • Posts: 1162
  • Hunter valley NSW
    • View Profile
Re: Info on new CR480 rod kit
« Reply #10 on: July 18, 2013, 07:07:12 pm »
Quote from: Matador107 on July 17, 2013, 09:51:08 pm
This bloke as well apparently he manufactures. Phil Denton Engineering in England.Hope it all helps.
Thanks for the heads up  ;) the bloke hes trying in the uk is phil denton as you said ;)
Thanks for the info lead montynut will let him know :)
Logged

Offline crabman

  • B-Grade
  • ***
  • Posts: 275
    • View Profile
Re: Info on new CR480 rod kit
« Reply #11 on: July 18, 2013, 07:18:08 pm »
Quote from: mick25 on July 15, 2013, 06:00:33 pm
A mate of mine is chasing a new rod kit for a 83 CR480 , any info where to get one will be tops.
I don't know if the 82 CR480 is the same or even the 84 CR500.
someone with a Honda zedder disc may know.
Thanks mick


You can get a new CR 480 rod kit from Phil Denton Engineering in the United Kingdom
web address www.phildentonengineering.com

Logged
Old and slow - and happy

Offline tony27

  • Legend
  • *****
  • Posts: 1908
    • View Profile
Re: Info on new CR480 rod kit
« Reply #12 on: July 18, 2013, 07:23:48 pm »
Another place to try would be trimac in Auckland, they've been making billet rods for various bikes for a while. Their work has been pointed out on here a few times, pretty sure they've sold both on trademe & ebay
Have a look at the video in about us, a billet Norton commando crankcase  :o

http://trimacmachining.com/index.html
Logged
Pages: [1]   Go Up
« previous next »