Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - crossedup2

Pages: [1] 2
1
General Discussion / Hodaka Information
« on: January 12, 2024, 08:48:34 AM »
Hi All

I may have the opportunity to buy a boxed up Hodaka. Has not run for at least 20 years. Located on a farm in the central west. Only thing I know is that it has the chrome tank. I will get it but is there anyone in Australia who deals with spares etc.

I wasn't looking for another project but this one is a bit left field, something to spice up the VMX juices in me.

Peter B


 

2
Wanted / Megacycle Cams for 82 XR500
« on: September 18, 2019, 10:27:23 PM »
Hi All
I'm in need of a 1982 XR500 Megacycle Cam Shaft ( the one with the needle bearings). The standard grind preferred.
Is there an agent in Australia? The USA store has limited access - and no email address >:( >:( >:(.

Or a good Second Hand XR head?????

Thanks in advance.
Peter B

3
Wanted / 1981/82 XR500 or XR250 Air Box Cover
« on: January 21, 2019, 09:02:51 PM »
Hi All

Looking for 1981 or 82 XR500 / XR250 air box cover.

And a bash plate for the above (500).

Thanks in advance.

Peter B

4
Wanted / MX125A /175A or YZ125A frame
« on: November 14, 2018, 02:03:57 PM »
Hi All

Looking for YZ125A or MX125A frame. (with swing arm if possible) Serial numbers start with 401 or 402.

Also looking for other bits for above if they are out there.

Thanks in advance.

Peter B

5
Yamaha / DG 125 HEAD
« on: June 04, 2016, 09:52:40 PM »
Hi All

What year did DG heads become available for yamaha YZ125's? I'm  guessing 1976 but can anyone firm that date.

Peter b

6
Wanted / MX125A or YZ125A seat .
« on: March 31, 2016, 09:37:53 PM »
Looking for the above seat. I'll even take just a good base but whole seat preferred.

Thanks in advance.

Peter B

7
Wanted / Need a mx125a or yz125c/x seat
« on: February 09, 2015, 10:04:27 PM »
Hi all

Looking for a seat for the above bikes. At least a reasonable base and foam for a new project. Anything reasonable considered. Thanks.

Peter Barber

8
Wanted / Dt250 D/E/F Motor (botom end) with electrics
« on: September 17, 2013, 05:24:49 PM »
Actually just need the crank, electrics and flywheel. Sydney area preferred.

Peter B
Thanks in advance.

9
Honda / Fitting a Postie CDI to an XL350
« on: August 26, 2013, 08:15:26 AM »
A friend has an XL350 with ongoing electrical problems. The spark is erratic at the best of times. Instead of buying stator coils etc he was hoping to replace the old system with something much more reliable. A bit of a search on the net and through previous posts says that a CDI unit out of a Postie bike is the fix so what and how is it fitted. None of the information goes into the How.

Any information would really be appreicated as he is trying to have it going (reliably) for the CRC in two weeks.

Thanks in advance.

Peter B

10
Tech Talk / Fixing dings in the side of a fork leg!
« on: September 23, 2012, 10:39:07 PM »
Hi All

Is there any one in the Sydney area who can fix a fork leg where something has banged up against it? There are 4 or 5 little dings mid way on one side which is now stopping the leg from sliding up and down on my YZ400D.

Alternatively, has anyone got a set of forks (YZ250D / YZ400D) where the chromes gone and not really usable but the bottom legs seem OK?

Any help appreciated

Regards

Peter B

11
Yamaha / Looking for a Classic Yamaha Jersy
« on: June 29, 2012, 04:35:42 PM »
Hi All

Looking for assistance to track down an old style riding shirt (or similar). Already contacted Vintage Iron but nil stock. Anywhere in Oz that may have one XL or XXL size? Yellow or White and prefer new.

Any assistance appreciated.



Peter B

12
Wanted / RT1 Frame needed.
« on: January 16, 2012, 10:08:49 PM »
About a year ago I did some dealing with Nathan S and ended up with his RT1 project. He did some cuts to the frame which could be dealt with but a dfferent original frame would make life easier.
The bottom end is RT2 and I'm not sure if there are any differences between RT1 & 2 or 3 frames. For that matter, I'm not sure if DT1 frames are the same and would be usable??? I need just bear frame and a bit of advise.

Prefered Sydney area if possible.
Peter B
0418 680 264 or email

13
Wanted / RT1 Barrel piston port
« on: November 21, 2011, 10:34:08 PM »
Hi all, looking for a reasonable barrel for friends RT1 pre 70 dirt tracker project. Any leads to one would be appreciated.

Peter B
0418 680 264

14
Wanted / Boyesen, Rad or Standard Reed petals for YZ400D
« on: April 30, 2011, 12:43:00 AM »
Hi All

Desperately looking for a set of Reed petals for a YZ400D/E. The box of bits that I bought that now resembles a motor is missing the reeds because someone has broken or removed them.

It appears that stock ones from any of the models below will fit.

Or Boyesen part number is #606 (fits YZ / MX / DT 360 and YZ400 up to 1978).

Thanks in advance.

Peter B
(Sydney Area)

15
Wanted / YZ250D / 400D Swing Arm Needed
« on: March 24, 2011, 08:49:32 PM »
Hi All

Looking for swing arm for a YZ400D project. Have one but the bearings had seized and the arm became the pivot point flogging it out. I've seen them in the States but just seeing if there is one locally before going off shore.

Peter B
0418 680 264

Pages: [1] 2