61
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
62
For Sale / VMXWA Bikes for Sale
« on: March 21, 2012, 07:47:45 pm »
One of the club stalwarts having a clean out might be worth a look in the For Sale - Bikes section, some great Bikes
http://vmxwa.com/
http://vmxwa.com/
63
Husqvarna / 1983 Husky CR500 Transmission Oil
« on: March 17, 2012, 01:02:00 pm »
anyone help with capacity and type
thanks
Barry
thanks
Barry
66
General Discussion / Closer to the Edge
« on: February 09, 2012, 04:31:18 pm »
Watched Closer to the Edge last night in 3D. Guy martin is mad, and bloody amazing. Just about needed subtitles to understand him. Great documentary with some reallyamzazing shots. Got my copy straight from UK, couldn't wait for it to come out here and it was probably around half the cost including postage. Only took about 8 days to get here
67
Wanted / Rickman zundapp metisse swing arm spindle
« on: January 01, 2012, 09:52:34 pm »
looking for a swing arm spindle for the above
68
British (BSA, Greeves, Triumph etc) / Rickman Zundapp Metisse Build
« on: December 07, 2011, 08:44:12 pm »
Well lets see what I've started with belong to a family friend and has sat under a tarp outside for about 30yrs or more. I want to rebuild it as a MX
Was given this
Today pulled and ground it apart. Have ended up with this
Problems already, as usual, can't get the swing arm pivot out totally solid.
The rear sprocket is also solid in the end of the swing arm
The triple clamp needs a 34mm socket, which i don't have
and i think you can see the corrosion and rust around the crank. The decision i have to make is whether to use this motor or find another as this is all i have of this one. The exhaust I have are the enduro model so was going to send it over to Brad and darryl Lewis and let them work their magic. I've just run over the frame with a wire wheel the welds are bloody brilliant and the rust not too bad. But i'll find an expert to give me abetter opinion. I have already ordered the plastics and tak from the UK. They aare being made courtesy of the Flkowerpot man ben Penny. Been a great help
Was given this
Today pulled and ground it apart. Have ended up with this
Problems already, as usual, can't get the swing arm pivot out totally solid.
The rear sprocket is also solid in the end of the swing arm
The triple clamp needs a 34mm socket, which i don't have
and i think you can see the corrosion and rust around the crank. The decision i have to make is whether to use this motor or find another as this is all i have of this one. The exhaust I have are the enduro model so was going to send it over to Brad and darryl Lewis and let them work their magic. I've just run over the frame with a wire wheel the welds are bloody brilliant and the rust not too bad. But i'll find an expert to give me abetter opinion. I have already ordered the plastics and tak from the UK. They aare being made courtesy of the Flkowerpot man ben Penny. Been a great help
69
Yamaha / MX360A Electrical
« on: November 28, 2011, 01:46:29 pm »
looking for a CDI and stator
Barry
Barry
70
Husqvarna / Wanted 1983 CR500 clutch cable
« on: October 03, 2011, 08:55:13 pm »
new bike, used clutch a couple of times, cable US, typical anyone got one
71
Wanted / 1983 Husky CR500 Clutch cable
« on: October 03, 2011, 08:48:30 pm »
Got the bike moved the clutch lever and pop. looking for a new one
Barry
Barry
72
Suzuki / RM250X rebuild or sell
« on: September 03, 2011, 11:43:25 am »
decisions, decisions, already have a rickman zundapp to do. Is the X worth the effort or should i sell on
73
Suzuki / Identification
« on: August 13, 2011, 07:20:04 pm »
just found a RM250 engine no 103001 anyone help with identification
monoi shock frame,
monoi shock frame,
74
Husqvarna / 1975 WR400 pre 75 eligibility
« on: June 22, 2011, 10:20:37 am »
Vin no MK20307 engine 20480396 would this be pre 75 eligible
thanks
Barry
thanks
Barry