« previous next »
Pages: [1]   Go Down

Author Topic: MX360A Petrol cap  (Read 2151 times)

0 Members and 1 Guest are viewing this topic.

Offline Tossa

  • Legend
  • *****
  • Posts: 2087
    • View Profile
MX360A Petrol cap
« on: May 10, 2011, 07:40:17 pm »
looking for one


regards

Barry
Logged
1973 Rickman Zundapp Metisse, to rebuild
1979 Husqvarna WR250
1974 Husqvarna MAG CR250

Offline Nathan S

  • Superstar
  • ******
  • Posts: 7275
  • HEAVEN #818
    • View Profile
Re: MX360A Petrol cap
« Reply #1 on: May 10, 2011, 08:04:39 pm »
Less than $40 for a new one from your local dealer.
Logged
The good thing about telling the truth is that you don't have to remember what you said.

Offline yamaico

  • Legend
  • *****
  • Posts: 816
    • View Profile
Re: MX360A Petrol cap
« Reply #2 on: May 10, 2011, 09:25:20 pm »
Hey Barry,

I've got one from these guys before. Cost is 16.45 english pounds ($25 Aus delivered). Includes the gasket, which some sellers don't.

http://cgi.ebay.co.uk/YAMAHA-DT250MX-DT400MX-DT-250-DT-400-FUEL-CAP-/230541495134?pt=UK_Motorcycle_Parts&hash=item35ad580b5e

Pete.
Logged

mx250

  • Guest
Re: MX360A Petrol cap
« Reply #3 on: May 10, 2011, 09:45:30 pm »
Quote from: Nathan S on May 10, 2011, 08:04:39 pm
Less than $40 for a new one from your local dealer.
Are the screw on fuel taps still available?
Logged

Offline jimg1au

  • Legend
  • *****
  • Posts: 3489
    • View Profile
Re: MX360A Petrol cap
« Reply #4 on: May 10, 2011, 10:11:26 pm »
mx250
i got 2 new ones from ebay uk the guy sells a lot of new trials stuff
jim
Logged

Offline Rossvickicampbell

  • Legend
  • *****
  • Posts: 3779
    • View Profile
Re: MX360A Petrol cap
« Reply #5 on: May 11, 2011, 09:32:25 am »
Barry - same same - I think I got one from the local Yamaha dealer.
Logged
1974 Yamaha YZ360B
1980 Honda CR250R - Moto X Fox Replica

Offline Tossa

  • Legend
  • *****
  • Posts: 2087
    • View Profile
Re: MX360A Petrol cap
« Reply #6 on: May 11, 2011, 10:24:47 am »
thanks guys
Logged
1973 Rickman Zundapp Metisse, to rebuild
1979 Husqvarna WR250
1974 Husqvarna MAG CR250

Offline Iain Cameron

  • Legend
  • *****
  • Posts: 2015
    • View Profile
Re: MX360A Petrol cap
« Reply #7 on: May 11, 2011, 09:11:28 pm »
Tossa check if you buy an old one some shrink and are a very loose fit  Iain
Logged
Yamaha tragic ; dt1, rt1, dt2, rt2, dt2mx , rt2mx , mx250, mx360,sc500, 74dt125, yzx125, yzc250, yzc400, yzd250, yzd400, yzh250, yzh80 , dt100 , xr75 ko xr80 03 , it175 82 . Not a member of any club

Offline Tossa

  • Legend
  • *****
  • Posts: 2087
    • View Profile
Re: MX360A Petrol cap
« Reply #8 on: May 12, 2011, 09:38:49 am »
that's exactly what has occured, just fell out on Sunday
Logged
1973 Rickman Zundapp Metisse, to rebuild
1979 Husqvarna WR250
1974 Husqvarna MAG CR250

Offline Iain Cameron

  • Legend
  • *****
  • Posts: 2015
    • View Profile
Re: MX360A Petrol cap
« Reply #9 on: May 18, 2011, 06:00:20 pm »
Tossa back in the early vmx mags there was a gent making alloy ones for HL,TY,MX,YZ . Ill look back and find the add ( 15 min later ) found it issue 14 page 65 HL500 billit fuel cap $80 made by Hanks Eng 07 40547144 .
Logged
Yamaha tragic ; dt1, rt1, dt2, rt2, dt2mx , rt2mx , mx250, mx360,sc500, 74dt125, yzx125, yzc250, yzc400, yzd250, yzd400, yzh250, yzh80 , dt100 , xr75 ko xr80 03 , it175 82 . Not a member of any club

Offline jimg1au

  • Legend
  • *****
  • Posts: 3489
    • View Profile
Re: MX360A Petrol cap
« Reply #10 on: May 20, 2011, 08:02:10 am »
Logged

Offline Canam370

  • Legend
  • *****
  • Posts: 1608
    • View Profile
Re: MX360A Petrol cap
« Reply #11 on: May 20, 2011, 08:29:49 am »
I purchased a new one from a local dealer recently. Don't forget to order the cork gasket too as it doesn't come with the cap ???. About $45 in total I recall.
Logged
WANTED. Canams;all models,complete or parts.SWM stuff too!

I'm THE Thread Killer - when I post a thread dies!

Offline Tossa

  • Legend
  • *****
  • Posts: 2087
    • View Profile
Re: MX360A Petrol cap
« Reply #12 on: May 20, 2011, 02:32:53 pm »
Yep got mine from local dealer with washer, $56.00.  Also needed a new gear change lever, yammie haven't changed the size of the spline (11mm) on the selector so was able to by a modern one exact same shape and size $25.00
Logged
1973 Rickman Zundapp Metisse, to rebuild
1979 Husqvarna WR250
1974 Husqvarna MAG CR250
Pages: [1]   Go Up
« previous next »