Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - 80-85 husky

Pages: [1] 2 3 ... 236
1
Here is a clip of the runner at a private track a while ago, have started on the scoot and have had Radchrome redo the fork tubes, cleaned greased and painted the front brake, cleaned the frame ready for blasting painting...trying to get a RAL code for the paint... starting to get keen.

biggest issue is the 3 4 and 5 gears...badly corroded in the bit sticking out of the gbox oil :-[ also the main gear shaft has some pits as well... thats what its all about..

https://youtu.be/Mm_xZ-snfa4

2
Vinduro / Re: Vintage Class A4DE
« on: April 20, 2018, 02:16:01 PM »
Didnt see a vintage bike in that....

3
For Sale / Re: original 80's Bell Moto 3 Helmet
« on: April 19, 2018, 07:39:39 PM »
Is the reinforced shelf to put it on also available ::)... ;D

4
Yamaha / Re: it465h rebuild
« on: April 18, 2018, 04:41:33 PM »
polished alloy or flat (satin) black is the go

5
VMX Sidecars / Re: Sidecar Racing
« on: April 17, 2018, 09:53:46 AM »
mate raced a kwaka 9 speedway outfit in the 80's. i had a ride on the chair once and decided ïts not for me"... his short career was interspersed with significant bingles. the best bingle had the outfit 10 metres in the air with the rider and passenger not far behind.. it landed on its back wheel..no more riding that day.

another close one was at the bendigo speedway when curly spun out in the first turn... he just got it straight when clarri jones who had bogged the start came thru and punted them down the straight back to racing speed and they were off and running.

6
Competition / Re: CD14 2018
« on: April 17, 2018, 09:45:37 AM »
Looks like its the Spanish for this VMX Magazines 20th Anniversary Celebration  8) 8)

have to fast fwd the moto villa resto!!  :-[

7
General Discussion / Re: Toll Warning $$$
« on: April 14, 2018, 08:26:02 AM »
25% of our sample population here just paid up... thats the plan....

8
Kawasaki / Re: Kawasaki KE100 compliance??
« on: April 11, 2018, 05:47:41 PM »
i used to ride around on a little kd 90 in the 80's. that had full vic reg

9
Suzuki / Re: HEEELLLLPPPP TS250X 1984 jet 6fjv54
« on: April 07, 2018, 08:31:27 AM »
not a lot of similarly btw the ts x and the rm. have you ridden them?

10
General Discussion / Re: Broadford Bike Bonanza 2018
« on: April 06, 2018, 06:12:07 PM »
last time i went i rode the track on a 400 enduro with 10" travel and it was fun until a short kicker jump which had a real splat landing hard down onto a flat ground gave  me a jolt in the shoulders and wrists every lap. On an old cr 250  greenback!!?? i couldnt entertain the thought at all. yet a youngish bloke the year before flogged an old bsa mx bike around there like he was mr mx. its the age factor i think. a lot of keen vmxer's over the last 10 years are hurting more and looking at vinduro short track etc.

11
A rattle gun will usually spin out the bolt without having to use a damper rod holder.

Even wacking an allen key with a hammer can sometimes crack them...leave the springs in and push down on the forks (upside down) to tension up the damper rod as you try to undo it.

12
General Discussion / Re: YZ400E
« on: April 02, 2018, 07:53:33 AM »
maxima 727 castor at 30:1 should be all you need. smeelllss so good (when your second) air filter clean? muffler freshly packed?

if your talking about the start up missing and clearing out till it warms up, all two strokes do that and dont worry about it.

if it does it all the time then try this...

sounds like your needle clip needs to be dropped 1 notch or lifted 1 to clean it up. if it hesitates or feels like its dragging a bit as you open up, the needle clip may need lifting 1 to lean it out a bit.

if its missing a bit as your roll on the throttle a bit, it may need lowering 1 clip to richen the mix going on to your main jet.

13
Tech Talk / Re: improving bottom end power
« on: April 01, 2018, 08:34:03 AM »
try leaning the needle 1 clip and see if this smooths the hit. does it feel like its dragging a bit before the top end rush? it may be a little rich on the bottom. you could try dropping the pilot jet 1 unit as well as get the airscrew out to 1.5 turns.

check the float level is right as well.

packing the muffler with steel wool instead of glass can also give more bottom end.

with the mods to the bike, its hard to make any simple suggestions without going "mechanical"as sleepy suggested.

14
Tech Talk / Re: Improvements to lathe
« on: March 31, 2018, 07:52:22 AM »
Wish i had a lathe.... :(

15
General Discussion / Re: just not cricket
« on: March 31, 2018, 07:50:14 AM »
i notice none of the other teams are screaming blue murder either...i suspect its a common practise but our dunderheads got caught...

Pages: [1] 2 3 ... 236