CLUB DAY 6TH SEPTEMBER BARLEIGH RANCH

[jimg1au]

there is a club day at b/r on sunday fathersday.can we have some details on the racing
what classes
gates open
sign on
ect ect ect
i am going booked my acc when booked for the nats
cheers
jim

[Noel]

Late edit

Just spoke to glen,
It is a club day,
so, there will be juniors and moderns as well as pre 85 and pre78/classic
one day membership of Hunter available ,
sign on from 730 Sunday.
Cheers
Noel

[Mick D]

Hi Noel, can you tell me what sort and size of dirt track tyre you run on your 125 dirt trackers please?
Might seem obvious to others, but I can only find 18 X 4.00s and I am new to this and wondering if a 125 will swing them? or is there a different option that you use?
Any help appreciated, thanks and regards Mick.

[Noel]

Hi Mick,
not running my 125's at dirt track this year,
but yes I was using 400 /18, but they were cheapies that did not work at all well on the 500,
do not know what a "michy" or IRC  would be like but think Nev run them on his 74 CR125 OK,
Cheers
Noel

[Rosco400]

there is a club day at b/r on sunday fathersday.can we have some details on the racing
what classes
gates open
sign on
ect ect ect
i am going booked my acc when booked for the nats
cheers
jim

Hi Jim
Bikes format at Hunter club day are pre 78 and pre 85 all in capacity, racing usualy gets underway around 10 for practise, try to get i four rounds through the day, Pre 78 and ride up in pre 85, scrutineeing and sign on between 8.30 to 9.00, day licence available, very relaxed atmospher

[Mick D]

Hi Mick,
not running my 125's at dirt track this year,
but yes I was using 400 /18, but they were cheapies that did not work at all well on the 500,
do not know what a "michy" or IRC  would be like but think Nev run them on his 74 CR125 OK,
Cheers
Noel

Thanks Noel, knowledge makes things so much easier than needlessly wasting money, cheers Mick.

[Rosco400]

You finally coming for a ride Mick

[jimg1au]

thanks for the replys
mick look at vrubber 400x18 not a bad rear for dirt track
i will be bringing my cr250 and cz400 i want to sort out the jetting on the 400 as it is only just rebuilt
cheers
jim

[Mick D]

thanks Jim, I was wondering if any one had been able to find a smaller(narrower)  version to run on the 125's. but Noel has more or less just clued me up thanks.

If you want a base line for your CZ400 mikuni jetting I will go and inspect my cz400 mikuni if youy like? it is allready of the bike? let me know if you want it's jetting spec's.
 

[jimg1au]

pm sent

[Mick D]

Sorry there Jim, big project. I got the mikuni off the cz400 and it's only a 32mm. Just goes to show ya what I know, 9/10th's of bugger all

I Haven't had spare grey matter or time to master picture posting yet, so Paul is about to do it for me.

I am thinking Ji may be able to help you. Good luck.
Mick.

[paul]

here ya go 

[Mick D]

Thanks Paul.

Hey Jim, PM Ji. I'am pretty sure he just set one up with a new 36mm Mikuni for the nationals.
It may even be here some where in his past posts.
God knows he posted everything else, hey Ji

[matcho mick]

whoo hoo ,well another great day at the office,another bloody good track,well done n run Hunter club,was a bit faster than Penrith,so guys leave your gearing the same  ,lot wider,the sweepers uphill onto start straight,will  be a good one for the nats, 

[Rosco400]

Was fun  good close racing in both classes, bring on the Nats