Author Topic: 1971 TM400 Engine Gasket Sealer  (Read 6633 times)

0 Members and 1 Guest are viewing this topic.

Offline TIKI

  • Novice
  • *
  • Posts: 19
    • View Profile
1971 TM400 Engine Gasket Sealer
« on: December 05, 2015, 09:30:17 pm »
Hello All,

 I am assembling a 1971 TM400 engine and wondering if gasket sealer is recommended on the new gasket between the 2 case halves, if so what product? There are no major imperfections but a few very light nicks in the aluminum.  I am more concerned with an air leak in the crankcase than transmission oil leak. I have the service manual which is very vague at best. Thanks Randy

 
1976 Yamaha DT400C , 1973 Kawasaki Z1 900 , 1971 Suzuki TM-400R Cyclone

Offline TTezza

  • B-Grade
  • ***
  • Posts: 281
    • View Profile
Re: 1971 TM400 Engine Gasket Sealer
« Reply #1 on: December 05, 2015, 10:06:23 pm »
Loctite gasket eliminator works for me


Offline TT5 Matt

  • Legend
  • *****
  • Posts: 1538
    • View Profile
Re: 1971 TM400 Engine Gasket Sealer
« Reply #2 on: December 06, 2015, 02:06:15 am »
grey 3 bond works well too, so good yamahas dont even use a centre case gasket ;)

Offline ITDOG

  • C-Grade
  • **
  • Posts: 66
    • View Profile
Re: 1971 TM400 Engine Gasket Sealer
« Reply #3 on: December 06, 2015, 06:30:04 am »
x2 on the three bond 8)

Offline bazza

  • Legend
  • *****
  • Posts: 2353
    • View Profile
Re: 1971 TM400 Engine Gasket Sealer
« Reply #4 on: December 06, 2015, 07:12:01 am »
 x3  on three bond :) :)
Once you go black  you will never go back - allblacks
Maico - B44 -1976 CR250- 66 Mustang YZF450,RM250
Embrace patina

Offline Oldfart

  • B-Grade
  • ***
  • Posts: 245
    • View Profile
Re: 1971 TM400 Engine Gasket Sealer
« Reply #5 on: December 06, 2015, 09:34:11 am »
Loctite 515  all day every day.

Offline shelpi

  • Legend
  • *****
  • Posts: 2056
    • View Profile
Re: 1971 TM400 Engine Gasket Sealer
« Reply #6 on: December 06, 2015, 10:04:14 am »
loctite 515
3 bond
aviation gasket sealant
no matter what you use still put the gasket in, for the correct spacing of gear box shaft shims ;)

Offline TIKI

  • Novice
  • *
  • Posts: 19
    • View Profile
Re: 1971 TM400 Engine Gasket Sealer
« Reply #7 on: December 07, 2015, 06:40:27 pm »
Thanks  for the replies guy’s. I guess I’m a little paranoid as I have not split the cases before. I have a can of Permatex spray copper and I think I will spray a light coat on each side of the gasket and call it good. The general consensus is with a gasket I really don’t need any sealer at all.

1976 Yamaha DT400C , 1973 Kawasaki Z1 900 , 1971 Suzuki TM-400R Cyclone

Offline matcho mick

  • Legend
  • *****
  • Posts: 2279
    • View Profile
    • Moto Tumbi
Re: 1971 TM400 Engine Gasket Sealer
« Reply #8 on: December 07, 2015, 10:34:54 pm »
a light spray that will work the best on the new gasket,good luck, :P
work,the curse of the racing class!!
if a hammer dosn't fix it,you have a electrical problem!!

Offline Lozza

  • Legend
  • *****
  • Posts: 4206
    • View Profile
Re: 1971 TM400 Engine Gasket Sealer
« Reply #9 on: December 07, 2015, 11:33:24 pm »
Wurth have a Threebond type instant gasket in a small pressure pack, much cheaper, easier to apply and no more wastage due to going off in the tube or nozzle. Think it was $36 for 300g can and trigger nozzle

https://eshop.wurth.com.au/Adhesive-and-sealing-compound-Super-RTV-silicone-SILSEAL-HIGHTEMP-SUPER-RTV-GREY-200ML/08933216.sku/en/US/AUD/
« Last Edit: December 07, 2015, 11:36:11 pm by Lozza »
Jesus only loves two strokes

Offline mick25

  • Legend
  • *****
  • Posts: 1162
  • Hunter valley NSW
    • View Profile
Re: 1971 TM400 Engine Gasket Sealer
« Reply #10 on: December 20, 2015, 08:57:12 pm »
Keep your gasket goo's in the beer fridge, in a plastic bag with a banana and they won't go off in the tube.
Good tip , I rember as a kid dad saying to mates if they have a wining diff put a banana in it  ::)
He tryed it on a old ford transit van it didn't work  ;D

Offline brent j

  • Legend
  • *****
  • Posts: 1435
  • Darwin, NT. Suzuki tragic, RL250M TS90MX PE250B
    • View Profile
Re: 1971 TM400 Engine Gasket Sealer
« Reply #11 on: December 20, 2015, 09:27:40 pm »
Keep your gasket goo's in the beer fridge, in a plastic bag with a banana and they won't go off in the tube.
Good tip , I rember as a kid dad saying to mates if they have a wining diff put a banana in it  ::)
He tryed it on a old ford transit van it didn't work  ;D

That Transit..........................I remember following a bus full of tourists on the dirt road around Opo with your dad full lock sideways on every corner at about 5km/h. Tourists didn't know what to think
The older I get, the faster I was

Offline mick25

  • Legend
  • *****
  • Posts: 1162
  • Hunter valley NSW
    • View Profile
Re: 1971 TM400 Engine Gasket Sealer
« Reply #12 on: December 20, 2015, 09:33:39 pm »
Keep your gasket goo's in the beer fridge, in a plastic bag with a banana and they won't go off in the tube.
Good tip , I rember as a kid dad saying to mates if they have a wining diff put a banana in it  ::)
He tryed it on a old ford transit van it didn't work  ;D

That Transit..........................I remember following a bus full of tourists on the dirt road around Opo with your dad full lock sideways on every corner at about 5km/h. Tourists didn't know what to think
That's the one Brent funny stuff
A Maori mate of dads borrowed the van to launch a boat off opo boat ramp
And he reckon the brakes failed it ended up under water to the roof , when they pulled it out of the drink it had a octopus on the drivers seat , only in opo hey
Sorry for the off topic

Offline PEZBerq

  • Legend
  • *****
  • Posts: 1094
  • Brisbane
    • View Profile
Re: 1971 TM400 Engine Gasket Sealer
« Reply #13 on: December 20, 2015, 10:10:36 pm »
Opo? Opotiki, Opononi? Whatchatalkingaboutwillis?
Husqvarnas: 78 390AMX, 82 430XC, 84 240WR, 84 500AE, 84 510TE, 87 510TE

Offline Lozza

  • Legend
  • *****
  • Posts: 4206
    • View Profile
Re: 1971 TM400 Engine Gasket Sealer
« Reply #14 on: December 20, 2015, 10:52:32 pm »
Keep your gasket goo's in the beer fridge, in a plastic bag with a banana and they won't go off in the tube.

No way I'd fall for that one  ;) ;D
Jesus only loves two strokes