« previous next »
Pages: [1]   Go Down

Author Topic: Honda XL250 are the parts interchangable to 350  (Read 2473 times)

0 Members and 2 Guests are viewing this topic.

Offline jimson

  • Legend
  • *****
  • Posts: 1308
  • Sanctuary point N.S.W
    • View Profile
Honda XL250 are the parts interchangable to 350
« on: September 13, 2013, 12:27:04 pm »
G,day viewers I have a early 70s Honda XL 350 and also 250 are any of the parts interchangeble. I want to keep the 350 but thought of selling the 250 both are 1973 engines. Jimson
Logged
Just a balless freak having a go

Offline matcho mick

  • Legend
  • *****
  • Posts: 2279
    • View Profile
    • Moto Tumbi
Re: Honda XL250 are the parts interchangable to 350
« Reply #1 on: September 13, 2013, 10:28:09 pm »
clutch cover,stator cover,stator/flywheel,(250's lighter?),gears,primaries,shift shaft,not much above crankcases,350 cams ok in 250,(but not the other way round ;)), :P
Logged
work,the curse of the racing class!!
if a hammer dosn't fix it,you have a electrical problem!!

Offline firko

  • Superstar
  • ******
  • Posts: 6578
    • View Profile
Re: Honda XL250 are the parts interchangable to 350
« Reply #2 on: September 13, 2013, 10:51:26 pm »
as well as what Mick said.....Rockers, carby,  ignition, (different but interchangeable) and nuts and bolts.
Logged
'68 Yamaha DT1 enduro, '69 Yamaha 'DT1 from Hell' '69 DT1'Dunger from Hell, '69 Cheney Yamaha 360, 70 Maico 350 (2 off), '68 Hindall Ducati 250, Hindall RT2MX, Hindall YZ250a , Cycle Factory RT2MX flat tracker, Yamaha 1T250J, Maico 250 trials, '71, Boyd and Stellings TM400, Shell OW72,750 Yamaha

Offline jimson

  • Legend
  • *****
  • Posts: 1308
  • Sanctuary point N.S.W
    • View Profile
Re: Honda XL250 are the parts interchangable to 350
« Reply #3 on: September 14, 2013, 07:16:54 am »
Thanks for that. Its worth keeping then  ;) Jimson
Logged
Just a balless freak having a go

Offline jimg1au

  • Legend
  • *****
  • Posts: 3489
    • View Profile
Re: Honda XL250 are the parts interchangable to 350
« Reply #4 on: September 14, 2013, 07:18:56 am »
gary
what do you want for them
are they side or center port
jim
Logged

Offline Tim754

  • Legend
  • *****
  • Posts: 4011
  • Northern Country Victoria
    • View Profile
Re: Honda XL250 are the parts interchangable to 350
« Reply #5 on: September 15, 2013, 07:29:30 pm »
Do up a 250 as a spare unit, bolts straight in ;)
Logged
I may not agree with what you have to say, but I'll defend to the death your right to say it.
                                                   Voltaire.

Offline FourstrokeForever

  • Legend
  • *****
  • Posts: 1702
  • AKA Mark H #35 VCM
    • View Profile
Re: Honda XL250 are the parts interchangable to 350
« Reply #6 on: September 19, 2013, 08:39:08 am »
Quote from: firko on September 13, 2013, 10:51:26 pm
as well as what Mick said.....Rockers, carby,  ignition, (different but interchangeable) and nuts and bolts.

Are you sure about the rockers being the same Mark? I have been told that they are a different ratio?
Logged
Arrogance.....A way of life for the those that having nothing further to learn.

Swiss

  • Guest
Re: Honda XL250 are the parts interchangable to 350
« Reply #7 on: September 27, 2013, 10:16:02 am »
The 250 vs. 350 rockers that I measured were slightly different in the width between the valves.  They would probably work but the adjuster pins won't be on center.  Pretty sure that the 250 that I measured was from a TL but I don't think there was any difference in valve spacing between the TL and XL250s.

Swiss
Logged
Pages: [1]   Go Up
« previous next »