Author Topic: first bike ready for d/t nats 2 more to go (Read 3279 times)

jimg1au · « **on:** September 26, 2012, 06:44:48 pm »

lucky i have next week off

Curly3 · « **Reply #1 on:** September 26, 2012, 06:47:41 pm »

Looking good Jim.
Gee you're doing it tough, haven't you just had a 2 month European vacation?

firko · « **Reply #2 on:** September 26, 2012, 08:01:05 pm »

I live for the day when we get to see Jims Monty with the original tank on board

jimg1au · « **Reply #3 on:** September 26, 2012, 08:15:41 pm »

well mark you know were both of them are dont you !!!!

matcho mick · « **Reply #4 on:** September 26, 2012, 08:24:49 pm »

fuggoff the pair of you

,

Freakshow · « **Reply #5 on:** September 27, 2012, 04:35:27 pm »

was not much point in doing that one, the H - pre 70 250 class was canned......... best you hurry up and move onto the other 2

jimg1au · « **Reply #6 on:** September 27, 2012, 06:08:29 pm »

it is entered in the pre 70 263 and over so i am takeing it
i ride against 650s and the biger bikes all the time at nepean so who cares.its just an extra ride plus back up for pre 75
jim

52 · « **Reply #7 on:** September 28, 2012, 11:43:31 am »

Looks good Jim!

Freakshow · « **Reply #8 on:** September 28, 2012, 12:26:36 pm »

you must have freinds in the right places

...... 263 and over, surely its now pre 70 all powers then.

jimg1au · « **Reply #9 on:** September 28, 2012, 01:39:16 pm »

yes i do
jim
thanks peter
no pushing me off when that big 750 passes me

Freakshow · « **Reply #10 on:** September 28, 2012, 01:54:08 pm »

i can hear the valves boucing from here...... the other 52

Sorelegs11 · « **Reply #11 on:** October 03, 2012, 09:22:30 am »

Hope the rest of your fleet gets together ok.
I was just putting the last new part on my dt3, new crank seal lh side when I removed the old seal to my horror a peice of the main bearing cage fell out

I dont think I have the motivation to put new mains in at this late stage $:-\$

jimg1au · « **Reply #12 on:** October 03, 2012, 12:08:42 pm »

bike no 2 now ready cz400
now for the cr250 flacttracker

matcho mick · « **Reply #13 on:** October 03, 2012, 12:36:45 pm »

errr, ossas done,(apart from fugging front brake $:-\$ ) t bone special

,hondas' engineless as i type,theres motors allover the floor atm,should be making the right noises tonite

,

jimg1au · « **Reply #14 on:** October 03, 2012, 04:09:47 pm »

just waiting for the seat to be finished from the motor trimmer put bigger muffle on
to do for no 3
repack muffler
number plates need an x
pick up seat and fix it is new
should be done tomorrow

OzVMX Forum

Author Topic: first bike ready for d/t nats 2 more to go (Read 3279 times)

jimg1au

first bike ready for d/t nats 2 more to go

Curly3

Re: first bike ready for d/t nats 2 more to go

firko

Re: first bike ready for d/t nats 2 more to go

jimg1au

Re: first bike ready for d/t nats 2 more to go

matcho mick

Re: first bike ready for d/t nats 2 more to go

Freakshow

Re: first bike ready for d/t nats 2 more to go

jimg1au

Re: first bike ready for d/t nats 2 more to go

52

Re: first bike ready for d/t nats 2 more to go

Freakshow

Re: first bike ready for d/t nats 2 more to go

jimg1au

Re: first bike ready for d/t nats 2 more to go

Freakshow

Re: first bike ready for d/t nats 2 more to go

Sorelegs11

Re: first bike ready for d/t nats 2 more to go

jimg1au

Re: first bike ready for d/t nats 2 more to go

matcho mick

Re: first bike ready for d/t nats 2 more to go

jimg1au

Re: first bike ready for d/t nats 2 more to go