« previous next »
Pages: [1]   Go Down

Author Topic: '74 MX250A Chain Gaurd  (Read 1230 times)

0 Members and 1 Guest are viewing this topic.

Offline PCMAX

  • B-Grade
  • ***
  • Posts: 254
    • View Profile
'74 MX250A Chain Gaurd
« on: August 05, 2012, 08:16:11 pm »
I'm looking for a 1974 MX250A chain gaurd p/n 322-22153-00-33
I am told this same part was also fitted to the following models; Anyone got one???
1972 DT2MX
1972 RT2MX
1973 MX250
1973 MX250A
1973 MX360
1973 RT2MX
1973 SC500
1974 MX360
1974 MX360A
1974 SC500A
1974 YZ250A
1974 YZ360A
1975 MX250B
1975 MX400B
1975 YZ250B
1975 YZ360B
1976 TT500C
Logged
74 MX250A, 75 CR250, 82 CR125, 82 YZ250J, 84 XR250,

Offline Iain Cameron

  • Legend
  • *****
  • Posts: 2015
    • View Profile
Re: '74 MX250A Chain Gaurd
« Reply #1 on: August 05, 2012, 10:05:50 pm »
to borrow to copy or keep ? Iain
Logged
Yamaha tragic ; dt1, rt1, dt2, rt2, dt2mx , rt2mx , mx250, mx360,sc500, 74dt125, yzx125, yzc250, yzc400, yzd250, yzd400, yzh250, yzh80 , dt100 , xr75 ko xr80 03 , it175 82 . Not a member of any club

Offline PCMAX

  • B-Grade
  • ***
  • Posts: 254
    • View Profile
Re: '74 MX250A Chain Gaurd
« Reply #2 on: August 06, 2012, 08:29:42 am »
Quote from: iainyz on August 05, 2012, 10:05:50 pm
to borrow to copy or keep ? Iain

Hopefully to buy from a friendly fellow VMXer.
« Last Edit: August 06, 2012, 08:33:32 am by PCMAX »
Logged
74 MX250A, 75 CR250, 82 CR125, 82 YZ250J, 84 XR250,

Offline Freakshow

  • Superstar
  • ******
  • Posts: 7277
  • Adelaide, SA - looking for a "YZA" tank
    • View Profile
Re: '74 MX250A Chain Gaurd
« Reply #3 on: August 06, 2012, 05:00:15 pm »
there not much chop unless you need it for a restor or somthing, its just Folded BAr almost....
Logged
74 Yamaha YZ's - 75 Yamaha YZ's
74 Yamaha  flattracker's
70  Jawa 2 valve speedway's

For sale -  PRE 75 Yamaha MX stuff, frame, motors and parts also some YAM DT1,2,A and Suzi TS bikes and stuff

Offline PCMAX

  • B-Grade
  • ***
  • Posts: 254
    • View Profile
Re: '74 MX250A Chain Gaurd
« Reply #4 on: August 06, 2012, 05:32:21 pm »
The parts manual shows a unit with a nice little chain roller fitted. VMX Unlimited sell these but no chain gaurd. I also need it (or something similar) to comply with the regs..........
Logged
74 MX250A, 75 CR250, 82 CR125, 82 YZ250J, 84 XR250,

Offline mick25

  • Legend
  • *****
  • Posts: 1162
  • Hunter valley NSW
    • View Profile
Re: '74 MX250A Chain Gaurd
« Reply #5 on: August 06, 2012, 06:15:25 pm »
I have a TT500c it has the same guard  you want , but still wont stop your fingers going in the rear sprocket section
The org guard is to far forward for protection for fingers etc
I made a custom guard up out of 3mm alloy plate that fits on the org mounts on the swing arm and it covers the start of the sprocket and chain
contact area.
Unless you want the org guard for a resto and keeping it all org.
I did see one on ebay NOS in the usa but went over $150 a few mths back. :'(
Logged
Pages: [1]   Go Up
« previous next »