« previous next »
Pages: [1]   Go Down

Author Topic: 1974 cr125  (Read 1231 times)

0 Members and 1 Guest are viewing this topic.

Offline dodgee

  • B-Grade
  • ***
  • Posts: 195
    • View Profile
1974 cr125
« on: April 27, 2011, 04:17:44 pm »
wanted top triple clamp and forks 4 a 1974/5 cr125
Logged

Offline Freakshow

  • Superstar
  • ******
  • Posts: 7277
  • Adelaide, SA - looking for a "YZA" tank
    • View Profile
Re: 1974 cr125
« Reply #1 on: April 27, 2011, 07:19:23 pm »
will swap a good set of cr125 forks currently being used in my YZ125a and in good condition with no pits no leaks - swap for some forks from yza/b,mx400b,250B etc. (see joan for details)

will also swap with the complete front CR Wheel and Backign plate on it too if you can pull me a rear or front YZ for a swap-see too   :)

may have other stuff to trade, but will check
« Last Edit: April 27, 2011, 07:22:04 pm by Freakshow »
Logged
74 Yamaha YZ's - 75 Yamaha YZ's
74 Yamaha  flattracker's
70  Jawa 2 valve speedway's

For sale -  PRE 75 Yamaha MX stuff, frame, motors and parts also some YAM DT1,2,A and Suzi TS bikes and stuff

Offline holeshot buddy

  • Legend
  • *****
  • Posts: 2008
  • sunshine coast qld
    • View Profile
Re: 1974 cr125
« Reply #2 on: April 27, 2011, 10:10:58 pm »
wayne i might have some triples what do
they look like (dont say they have holes in them for forks) ::)
Logged
follow me to first turn

Offline dodgee

  • B-Grade
  • ***
  • Posts: 195
    • View Profile
Re: 1974 cr125
« Reply #3 on: April 28, 2011, 07:53:06 am »
yes russ they do 31 mm to be exact
Logged

Offline Freakshow

  • Superstar
  • ******
  • Posts: 7277
  • Adelaide, SA - looking for a "YZA" tank
    • View Profile
Re: 1974 cr125
« Reply #4 on: April 28, 2011, 01:13:05 pm »
they fit in the 30mm YZa125 tripples as well, which is what these ones are in currently.
Logged
74 Yamaha YZ's - 75 Yamaha YZ's
74 Yamaha  flattracker's
70  Jawa 2 valve speedway's

For sale -  PRE 75 Yamaha MX stuff, frame, motors and parts also some YAM DT1,2,A and Suzi TS bikes and stuff

Offline smed

  • Legend
  • *****
  • Posts: 1646
    • View Profile
Re: 1974 cr125
« Reply #5 on: April 28, 2011, 03:35:30 pm »
Believe it or not,the top clamp is identical to ct125/200 ag bike,the aggy has extra mounts cast in for the speedo,when i got my 74 cr125 the top clamp was broken, I matched them up to a set of the aggy ones at the local wreckers, I noticed on my original clamps where the lugs had been ground off,so thats what i done & they are still on there! The bottom clamp might also fit but they are steel not alloy,also the forks are very similar,of course i would assume the springing & damping would be different, both front & rear hubs look the same too, Now, no wise cracks about the elsie 125 just being a tarted up cockys bike :P
Logged
Pages: [1]   Go Up
« previous next »