Topics

1

General Discussion / Photo attaching

« on: February 16, 2021, 12:32:02 PM »

Hi everyone, It's been a few years since I have been on the forum and I seem to have forgotten how to attach photo's to my posts. I have photo bucket and it's active again.
Is there a step by step post that I can read up on please?

Regards Stan.

2

General Discussion / Mr Mx program's from any Amaroo rounds in 1974 or 1975

« on: August 19, 2013, 12:57:47 PM »

Does anyone still have program's for 74 or 75 Mr Mx rounds at Amaroo please.

Stan.

3

For Sale / IT125 NOS expansion chamber

« on: August 01, 2013, 09:49:51 PM »

I have an IT125 pipe for sale but NO muffler. Has a few minor marks from being shifted around over the years and some bits of old packing tape stuck to it . $250.00

Stan.

4

Spaniards (Bultaco, Ossa, Montesa etc) / Bultaco's on Gumtree

« on: July 24, 2013, 07:12:21 PM »

Here's a few Bultaco's my son found for sale by the same seller on Gumtree.

Stan.

http://www.gumtree.com.au/s-ad/hobart-region/motorcycles/bultaco-matador-250/1024168463

http://www.gumtree.com.au/s-ad/hobart-region/motorcycles/bultaco-frontera-mk-11-370/1024167636
 
http://www.gumtree.com.au/s-ad/hobart-region/motorcycles/bultaco-mk-11-pursang-250/1024168209

5

General Discussion / Who's the Birthday Girl then?

« on: July 24, 2013, 07:49:24 AM »

  Happy birthday Ali.

Regards Stan.

6

Tech Talk / Hot pressure wash cabinet

« on: July 11, 2013, 09:02:30 PM »

Well, I needed to hot wash some dirty parts (too cold outside this week -4 deg one morning) so I connected my Karcher hot wash up to a spare bead blast cabinet, fitted some waterproof rubber gloves, shortened up a pressure wash lance and added a windscreen wiper to the inside, ran some silicone around the cabinet joints, ran the outlet through the wall to a home made grease trap and fired it up. Works a treat.
Makes life very easy getting things clean.

Stan.

7

Tech Talk / Recycled bike work stand

« on: July 11, 2013, 01:42:58 PM »

Just thought I would show some photo's of my new work stand recycled from an old hospital bed with an electric lift. They were giving these away so I thought I would give one a try. I still have to fit the pivoting ramp to it yet to finish it off.

Stan.

8

Foto Forum / Views of Melbourne

« on: July 11, 2013, 12:01:07 AM »

Hope you like my favourite views of Melbourne

Stan.

9

Wanted / KDX175 parts wanted

« on: July 03, 2013, 09:59:32 PM »

Can anyone help with some 82 KDX175 parts. I need a rear brake backing plate assembly, a rear brake rod and a rear brake stay rod.

Thanks Stan.

10

For Sale / NOS 83 KX500 cylinder for sale.

« on: June 19, 2013, 09:00:01 PM »

I would like to sell a NOS 83 KX500 cylinder that I have spare. Price is $500 plus postage.

Stan.

11

Vintage Track / Speedway chain

« on: April 10, 2013, 08:31:00 PM »

Can anyone recommend a brand/type of primary and drive chain to use on a J.A.P/Jawa speedway bike I have recently purchaced.

Stan.

12

Bike Transport / Cairns to Ballarat

« on: February 28, 2013, 10:54:54 PM »

Can anyone help with a bike from Cairns down to Victoria. I'm in Ballarat but I could pick up anywhere in Vic.
Happy to pay costs.

Stan.

13

Bike Transport / Sydney to Ballarat

« on: September 19, 2012, 07:13:02 PM »

Help needed to get a bike from Eastwood in NSW to Ballarat Victoria. Happy to help with fuel costs.

Stan.

14

General Discussion / Does anyone know this guy on Mark's Swapmeet

« on: July 16, 2012, 07:43:40 PM »

Has anyone had any dealings with Joe Adomaitis, Sewell, NJ as I emailed him regarding some KX parts he has on Marks Swapmeet.

This was my question:

"Hi Joe, how much would you charge to send the shocks and tank to me in
Australia, post code 3356 please.
If postage is reasonable I will buy them. Do you have anything else for
early KX`s"

This was his response:

"I'm not saying, you figure it out.Just get a idea of what it will cost .If your still interested  we'll work out a finally  cost"
 
http://www.vintagemx.us/cgi-bin/largephoto.cgi?C=jwsAXBeMQ11WSN8q

15

Tech Talk / Vapour Blasting in Victoria

« on: July 15, 2012, 10:54:32 PM »

Can anyone recommend a Vapour Blasting business in Victoria.

Stan.