Topics

1

Wanted / Wanted ADB Magazine early issues

« on: September 27, 2022, 11:16:25 pm »

Hi
I'm looking for any reasonable copies from 1975 - early 80's.

2

Honda / CR250M'76 Fork caps

« on: April 12, 2022, 11:00:52 am »

Not sure if this bike has standard fork caps - they don't appear to screw in and have right-angled air valves. Left side looks like it's leaking.

3

Honda / CR250M wide pegs

« on: April 10, 2022, 09:11:31 am »

Does anyone know which wide pegs will fit a '76 CR250M?

4

KTM / Bottom Coils '81 250MC

« on: December 12, 2019, 11:45:13 am »

They're stuffed...anybody got some??

5

KTM / Sprockets

« on: May 10, 2019, 06:28:03 pm »

What's the best source for sprockets for my '82 250MC?

6

Yamaha / Stainless spoke sets

« on: May 05, 2019, 02:53:06 pm »

Can anyone advise where to source these for my YZ125D?

7

KTM / Marzocchi assembly

« on: October 24, 2018, 06:51:10 pm »

Hi there - need advice! Installed new fork seals in my 40mmm forks - 40x52x10. I can't get them to seat low enough to fit the wipers. Put the washer on top, then circlip as advised, but the groove the circlip sits in doesn't allow enough room for the wiper? I also found that the left leg had long spring, 2 short and 1 top out, but right had no top out.
Hi

8

Yamaha / YZ125D motor

« on: May 01, 2017, 09:07:13 pm »

Anybody got one?

9

Husqvarna / 82 wr240 fork oil capacity

« on: April 21, 2017, 09:23:50 pm »

Hi

Can anyone tell me the fork oil capacity (level) for my Husky? 35mm...

Hoping to have it running at Gloucester.

10

Suzuki / RM250/400N/T shock springs

« on: February 15, 2017, 12:11:44 am »

Wondering if anyone has a decent standard set? I need them to put on a set of Ohlins.

Cheers, Paul

11

Husqvarna / 17" tyres

« on: February 05, 2017, 08:36:41 pm »

Can anyone tell me the best option for a 17 tyre for my 240? It's also missing a spoke - are they available?

12

KTM / Pistons?

« on: January 26, 2017, 05:53:23 pm »

I've decided to do a top end rebuild in my '82 250MC. It's standard bore so 1st OS...what's the best choice for piston? Are those aftermarket reeds worth it?

Thanks, Paul

13

Yamaha / Kick start return spring

« on: January 05, 2017, 03:58:12 pm »

Hi - hoping someone can give me some guidance in reinstalling/resetting the kick start return spring in a DT175 (1980). The engine's fitted into a YZ125D frame. It had an intermittent noise in the motor so I took off the clutch case looking for something obvious. All I have found is the clip holding the kick start gear in place wasn't seated in the groove - it was unseated at both ends. I've fixed that but now I can't figure out how to set the return spring. The motor/gears/clutch were all running fine - just this grinding noise every so often which then became louder. I don't particularly want to strip the motor as I don't really know what I'm doing...

Cheers, Paul

14

Husqvarna / Tank '82 240WR

« on: December 14, 2016, 06:03:12 pm »

Hi.
Does anyone have a tank they don't want? I want to moth ball the restored tank I have and use an average one for riding. I'd prefer the earlier shape WR tank.

15

Yamaha / YZ125D side plates

« on: December 12, 2016, 08:22:53 pm »

Hi. Does anyone know a source for YZ125D side plates (white)?

Cheers, Paul