1
Yamaha / Re: yamaha mx 250 question
« on: June 25, 2018, 10:58:29 am »
My Jones Products Tank is now on my Facebook page.Look under Bill Davis or under Firko's or Iain's as I'm friends of both.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2
Yamaha / Re: yamaha mx 250 question
« on: March 26, 2018, 01:37:20 pm »
Hey guys I can't get the pix of the Jones Products Clutch Cover to load here but you can see it on my Facebook page.
3
Yamaha / Re: yamaha mx 250 question
« on: March 22, 2018, 12:49:06 pm »
Iain
I have a Jones Products Clutch Cover on one of my PDV's.
What I've been looking for is some Jones forward axle fork
lower legs for early DT or YZ's.I've heard they had Jones Products cast on them but I've never seen any.
I have a Jones Products Clutch Cover on one of my PDV's.
What I've been looking for is some Jones forward axle fork
lower legs for early DT or YZ's.I've heard they had Jones Products cast on them but I've never seen any.
4
Yamaha / Re: yamaha mx 250 question
« on: March 22, 2018, 12:43:03 pm »
Kenny If my memory is correct.The DT/RT2MX silencers had a plug you could knock out so they became strait through.As I recall they did run better after this but were a little louder.
5
Yamaha / Re: yamaha mx 250 question
« on: March 21, 2018, 12:08:58 pm »
Iain !!
The one I have is the only one I've ever seen until the one posted above.I was going to use it on a PDV project that I was going to use a YZ type
crossover pipe rather than the leg toaster DT1MX style pipe they came with.I had a machinist modify one of the rear down tubes for clearance but was not happy with it and kinda lost interest in it.
The one I have is the only one I've ever seen until the one posted above.I was going to use it on a PDV project that I was going to use a YZ type
crossover pipe rather than the leg toaster DT1MX style pipe they came with.I had a machinist modify one of the rear down tubes for clearance but was not happy with it and kinda lost interest in it.
6
Yamaha / Re: yamaha mx 250 question
« on: March 19, 2018, 09:05:52 am »
Kenny !!!
I have a tank like yours and was told it was a Jones Products Tank.
Bill Davis Texas Vintage Racing Club
I have a tank like yours and was told it was a Jones Products Tank.
Bill Davis Texas Vintage Racing Club
7
Vintage Track / Assault on America !!!
« on: March 04, 2018, 01:40:36 pm »
Hey Mates !!
How about some support for 2 Buds Racing's Pete Lee and David Gras with their assault on the Yankee US riders at various races around Daytona in a couple of weeks.They're bringing their Bodyguard " The Boomer" as well.
Let's hear it !!!
Bill Davis Texas Vintage Racing Club
How about some support for 2 Buds Racing's Pete Lee and David Gras with their assault on the Yankee US riders at various races around Daytona in a couple of weeks.They're bringing their Bodyguard " The Boomer" as well.
Let's hear it !!!
Bill Davis Texas Vintage Racing Club
8
General Discussion / Re: Yamaha 360 Pistons
« on: January 09, 2018, 01:21:58 pm »
Hey Mates.I have a ton of Yamaha 250 & 360 pistons if you can't find what your looking for.Let me know.
Bill Davis Texas Vintage Racing Club
Bill Davis Texas Vintage Racing Club
9
Yamaha / Re: dt1 question
« on: December 12, 2017, 02:36:17 pm »
Still around Mates.Hoping to come over again next year with my wife.She's never been.Any Racing over there in January or February 
10
Yamaha / Re: dt1 question
« on: December 11, 2017, 02:10:10 am »
Or use a 74/75 YZ head.They would just have extra holes as would the DT2MX.
Bill Davis Texas Vintage Racing Club.
Bill Davis Texas Vintage Racing Club.
11
Yamaha / Re: YZ Clutch Cover on DT1-RT1 cases
« on: June 06, 2017, 06:56:21 am »
The clutch covers fit the bolt pattern and gasket but the kick start shaft is different on the YZ.If you don't change it,the cover cracks around the seal when you tighten it up.The DT/RT shaft can be modified by making a new groove for the snap ring further in.I think it was about 1/4 inch but I haven't done one in years.I hope this helps.If you can't figure something out let me know and I'll pull one of mine apart to see the distance.
Bill Davis Texas Vintage Racing Club
Bill Davis Texas Vintage Racing Club
12
Yamaha / Re: YZ360B piston
« on: July 29, 2015, 12:50:34 pm »
Hey Husky !!!
I think I have one if you can't find any over there.Let me know.
Bill Davis Texas Vintage Racing Club.
I think I have one if you can't find any over there.Let me know.
Bill Davis Texas Vintage Racing Club.
13
Competition / Re: Celebrating 20 years @ Dandaloo Park WA
« on: May 06, 2015, 11:56:56 am »
Great track and even greater people.I attended the Nationals there in 2006 and loved the experience.
14
Wanted / Re: Wanted 1974 YZb side covers
« on: May 20, 2014, 12:40:55 pm »
Hey Ian !!!
All I could find was a couple of sets of homemade fibreglass number plates a guy made for me years ago.They're kinda thin and not smooth but fit well and look good at 50 MPH and 200 feet away.The only 250 heads I found were a stock DT2MX and a DT2MX head that's been shaved to look like a 431 YZ250A head.I also had the extra 4 holes drilled in the head for the smaller 8 MM studs.
Let me know.
All I could find was a couple of sets of homemade fibreglass number plates a guy made for me years ago.They're kinda thin and not smooth but fit well and look good at 50 MPH and 200 feet away.The only 250 heads I found were a stock DT2MX and a DT2MX head that's been shaved to look like a 431 YZ250A head.I also had the extra 4 holes drilled in the head for the smaller 8 MM studs.
Let me know.
15
Wanted / Re: Wanted 1974 YZb side covers
« on: May 19, 2014, 01:03:54 pm »
Ian !!!
Do you need a 250 or 360 head I'll see what I have. I know I have a good set of side covers.
Do you need a 250 or 360 head
I'll see what I have. I know I have a good set of side covers.