1
Honda / Re: CR250M rear sprocket WANTED
« on: October 01, 2022, 10:09:17 pm »
I've had an adapter machined for a flat sprocket - great job, looks neat and works a treat.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2
Wanted / Wanted ADB Magazine early issues
« on: September 27, 2022, 11:16:25 pm »
Hi
I'm looking for any reasonable copies from 1975 - early 80's.
I'm looking for any reasonable copies from 1975 - early 80's.
3
Honda / Re: CR250M rear sprocket WANTED
« on: April 24, 2022, 09:03:16 am »
Thanks Bazza - out of stock though. Sprocket Specialists not doing them anymore.
4
Honda / Re: CR250M'76 Fork caps
« on: April 24, 2022, 08:58:42 am »
Thanks Noel, I'll attempt to get them apart. They're obviously aftermarket or modified.
5
Honda / Re: CR250M'76 Fork caps
« on: April 22, 2022, 11:35:39 am »
Thanks Noel - not leading axle. I've got photos but can't see how to post them on here?
6
Honda / Re: CR250M rear sprocket WANTED
« on: April 21, 2022, 04:13:32 pm »
I'm getting a spacer made up to run flat sprocket with counter-sunk bolts.
7
Honda / Re: CR250M'76 Fork caps
« on: April 21, 2022, 04:11:17 pm »
No John, They're circular - sit below the top of the fork and don't screw in - they spin freely but are definitely fixed.
8
Honda / CR250M'76 Fork caps
« on: April 12, 2022, 11:00:52 am »
Not sure if this bike has standard fork caps - they don't appear to screw in and have right-angled air valves. Left side looks like it's leaking.
9
Honda / CR250M wide pegs
« on: April 10, 2022, 09:11:31 am »
Does anyone know which wide pegs will fit a '76 CR250M?
10
Honda / Re: CR250M rear sprocket WANTED
« on: March 09, 2022, 04:25:53 pm »
Hey
Did you have any luck? I'm looking for the same thing.
Did you have any luck? I'm looking for the same thing.
11
KTM / Bottom Coils '81 250MC
« on: December 12, 2019, 11:45:13 am »
They're stuffed...anybody got some??
13
Yamaha / Stainless spoke sets
« on: May 05, 2019, 02:53:06 pm »
Can anyone advise where to source these for my YZ125D?
14
KTM / Re: Marzocchi assembly
« on: October 25, 2018, 09:25:48 am »
Thanks guys
I should have checked the height of these seals - I can't see what else could cause this but that the seals are a few mm higher. I think I'll trim the covers and silastic them in. Should be fine...
I should have checked the height of these seals - I can't see what else could cause this but that the seals are a few mm higher. I think I'll trim the covers and silastic them in. Should be fine...
15
KTM / Marzocchi assembly
« on: October 24, 2018, 06:51:10 pm »
Hi there - need advice! Installed new fork seals in my 40mmm forks - 40x52x10. I can't get them to seat low enough to fit the wipers. Put the washer on top, then circlip as advised, but the groove the circlip sits in doesn't allow enough room for the wiper? I also found that the left leg had long spring, 2 short and 1 top out, but right had no top out.
Hi
Hi