Messages

1

Wanted / Wanted 1974 TS100 petrol cap

« on: March 20, 2019, 08:58:03 pm »

Hey,
I am on the hunt for a 1974 TS100 (small hole) petrol cap. I brought one, but it's too big. Need it in a hurry, PLEASE HELP! Leads appreciated

Thanks,
Mark

2

Wanted / 1968 Suzuki T200 Crank NEEDED

« on: December 11, 2018, 08:41:39 pm »

Hi,
I had my crank pressed apart and the bearing surfaces are no good. It must of been sitting in water for 20 years. I got hold of a second bottom end and it is stuffed too! If you have a T200 crank weighing you shelf down, please give me a call. Cheers Mark 0408271831 

3

Wanted / Re: 1968 Suzuki T200 X5 Scrambler Crank pins

« on: December 11, 2018, 08:33:52 pm »

I found some, they where 19mm. I brought 1 on eBay.com then soon after 2 came up for sale. Now I have one spare.
Thanks for your help, I haven't had much luck

4

Wanted / 1968 Suzuki T200 X5 Scrambler Crank pins

« on: October 24, 2018, 05:57:51 pm »

Hi all,
I have been trying for months to get my hands on a pair of crank pins. Mine are rusted solid, along with just about every moving part. Even the carbs were festered into solid blocks. Have got everything together minus the crank pins. Good used ones or new would be super helpful!
Any help would be greatly appreciated
Thanks,
Mark

5

Wanted / Re: Wanted IT490 Black Fork Boots

« on: October 20, 2018, 07:52:14 pm »

Cheers mate!

6

Wanted / Wanted IT490 Black Fork Boots

« on: October 19, 2018, 11:53:08 pm »

Any ideas on fork boots without expensive o's postage?

7

Wanted / XT500 HL style, small parts needed

« on: January 22, 2018, 07:19:57 pm »

Hi all,
I put my bike on the back burner, (again) for a while now. Looking to finish her off. I need,
Headlight ring (I have one with a few scars)
Mirrors
Steel rear guard
Cable guide (mounts on front fork leg)
Rear tail light

Planning to put her on Historic rego. Any help appreciated.
Cheers Mark

8

Wanted / Re: XT550/600 Carburetor.

« on: December 11, 2016, 09:32:18 pm »

I will dig it out and take some photos. See if it is what your looking for.

9

Wanted / Re: XT550/600 Carburetor.

« on: December 09, 2016, 11:34:36 pm »

Hi Curtis,
I have 1985 TT600 stock carby, just got them with a motor, never used or run them but they look ok.
Not sure if they are the same as the XT, welcome to check it out, in Sydney

10

Wanted / Re: Wanted Basic Motorcycle dyno Sydney or NSW

« on: September 11, 2016, 08:13:17 pm »

Carl at Cafe Racer, at Wattle Flat (best mechanic around)

11

Wanted / Re: Wanted 18" paddle tyre, or Any Outragous 18" rear 21" front combination

« on: September 11, 2016, 08:11:01 pm »

Do you have any 21" front, to go with it or reccomendation

12

Wanted / Re: Wanted 18" sand tyre, or Any Outragous 18" rear 21" front combination

« on: September 10, 2016, 08:43:22 pm »

Yeah! Sorry, a paddle tyre!

13

Wanted / Wanted 18" paddle tyre, or Any Outragous 18" rear 21" front combination

« on: September 10, 2016, 12:18:05 pm »

Hey,
Anyone got a sand tyre in good Nic? 18" rear Thanks 0408271831 Mark

14

Wanted / Re: XT 500 or XT600 Bits needed

« on: March 21, 2016, 09:57:34 pm »

I've got an XT550 that I'm wrecking. Those parts any good?

Thanks mate, I managed to pick up the 500 bash plate and case!

Appreciate the offer

15

Wanted / XT 500 or XT600 Bits needed

« on: March 04, 2016, 09:00:53 pm »

Hi all,
I have returned to my rebuild after a lengthy abstinence. It got the better of me for a while, but have seen the light at the end of the tunnel ?
Has anyone got a toasted engine case for xt600 or a xt500
An aluminum bash cover for a XT500 in polishable condition

Any help appreciated
Mark