OzVMX Forum

Marque Remarks => Yamaha => Topic started by: Davy123 on October 14, 2019, 04:27:19 am

Title: DT2MX
Post by: Davy123 on October 14, 2019, 04:27:19 am

I need a shorter kick start on my DT2MX .. anyone any ideas what would fit ?

Title: Re: DT2MX
Post by: bazza on October 14, 2019, 09:33:21 am

Use the search box at top of page - answer will be in archives as discussed a lot years ago

Title: Re: DT2MX
Post by: Davy123 on October 14, 2019, 05:41:52 pm

I did , no matches were found ..hence I'm asking here ..

Title: Re: DT2MX
Post by: Iain Cameron on October 14, 2019, 08:27:19 pm

DT 250/360/400 74 75 76 77 . MX 250 /360 /400 73 74 75  Sc500 73 74 . YZ  250 /360/ 400  74 /75/ 76 /77 . DT 1 2 3  RT 1 2 3 . ( early DT and RT are not folding ) they will all fit .

Title: Re: DT2MX
Post by: Davy123 on October 14, 2019, 10:55:54 pm

Thanks ... Much appreciated ????

Title: Re: DT2MX
Post by: Momus on October 15, 2019, 01:01:19 am

Scarfed weld line cut-and-shut is an option as well.

Title: Re: DT2MX
Post by: John Orchard on October 15, 2019, 10:33:15 am

Quote from: Iain Cameron on October 14, 2019, 08:27:19 pm

DT 250/360/400 74 75 76 77 . MX 250 /360 /400 73 74 75  Sc500 73 74 . YZ  250 /360/ 400  74 /75/ 76 /77 . DT 1 2 3  RT 1 2 3 . ( early DT and RT are not folding ) they will all fit .

Would TT/XT500 be in there too?

Title: Re: DT2MX
Post by: Iain Cameron on October 16, 2019, 07:04:37 pm

Yes the TT and XT but I haven't tried them so I didn't put them up .

Title: Re: DT2MX
Post by: Davy123 on October 17, 2019, 05:18:37 am

i think i'll just heat and put an s bend in the standard one.... cheers anyway for the replies..

Title: Re: DT2MX
Post by: crossedup2 on October 19, 2019, 10:33:21 am

I'm currently running an RD250 kicker on my RT1. I know you want shorted but it needs to be added to the list.

Title: Re: DT2MX
Post by: Iain Cameron on October 19, 2019, 03:57:16 pm

Why do you want a shorter one Davy123 ?

Title: Re: DT2MX
Post by: Davy123 on October 20, 2019, 03:55:58 am

...iain.. it hits the aftermarket pipe that i have fitted .. DT2MX in  PDV frame...i dont even know if the kickstart is correct ,i'd send you a photo but i dont know how..

Title: Re: DT2MX
Post by: GMC on October 21, 2019, 03:17:47 pm

Quote from: Davy123 on October 17, 2019, 05:18:37 am

i think i'll just heat and put an s bend in the standard one.... cheers anyway for the replies..

I wouldn't recommend heating and bending a kick start lever as it will soften the material and will most likely bend easy.

Title: Re: DT2MX
Post by: Iain Cameron on October 22, 2019, 04:27:21 pm

Davy 123 try a 74/75/76 Yamaha TY250 kick starter . about 2.5inch shorter .

Title: Re: DT2MX
Post by: Davy123 on October 24, 2019, 05:54:57 am

iain ... cheers.. i sent you photo on facebook..