Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Freakshow

Pages: 1 2 [3] 4 5 ... 485
31
Yamaha / Re: yamaha MX 1974 fuel tanks
« on: May 09, 2016, 02:06:00 pm »
how much you wanna spend ?

32
General Discussion / Re: Project management software
« on: May 09, 2016, 02:00:48 pm »
Excell is so easy and mine have look up and filters, you can even use the priovt table etc.  profit / loss you create the work flow. 

33
Wanted / Re: DT2/3 RT2/3 oil tank wanted
« on: April 14, 2016, 02:18:03 pm »
ID have some for sure. any colour ?

34
Wanted / Re: YZ250A alloy sprocket cover/clutch actuator
« on: April 14, 2016, 02:17:18 pm »
that bikes missing its plastic vent riser, dirt and water loves that hole.

35
Wanted / Re: YZ125d-e-f or g carb/complete engine
« on: April 14, 2016, 02:16:09 pm »
i have a motor and rubber, i can test it against a DT if you tell me what Dt.  the early stuff has smaller reads and closer spaced bolt holes.  I think the 18G is the first rubber that the wider size and bigger reeds come on.  pre that its all same as YZ125A

36
Wanted / Re: MX125A or YZ125A seat .
« on: April 14, 2016, 02:14:23 pm »
Also yz100 will fit you just need longer ears bolted off the 125 to reach the seat bolt hole.

37
General Discussion / Re: lost a donk in the post
« on: March 30, 2016, 05:28:31 pm »
Pete when you say posted ? was it a complet motor and how was that shipped not over weight ???? please explain.  also cost.

I need some wheels shipped out.

38
Yamaha / Re: yamaha MX 1974 fuel tanks
« on: March 29, 2016, 04:22:39 pm »
What vandy said
they 125 and 175 fit at the front but you need to move a bolt hole mount on the rear forward about an inch.

39
Wanted / Re: Yamaha MX 400 Fuel petcock spigot
« on: March 21, 2016, 03:06:44 pm »
comes on the Fuel tap, just find another and raid it

40
Wanted / Re: Suzuki tm 125 barrel.
« on: March 21, 2016, 03:05:55 pm »
if you have one and just need it resleeved Nipper, i can get that and fitted for about $330 if that helps

41
Wanted / Re: yamaha mx/yz 250/360/400 b/c rear monoshock
« on: March 21, 2016, 03:04:59 pm »
since when did the US make ordinary products ?

42
Wanted / Re: Yamaha SC500 parts
« on: March 21, 2016, 03:04:00 pm »
rims online.
seat is same as MX250/360/500
plates same as mose yams

43
Wanted / Re: YZ250A workshop manual
« on: March 21, 2016, 03:01:56 pm »
just use a DT/RT one mick, internally all the same

44
Wanted / Re: YAMAHA DT2MX PARTS
« on: March 21, 2016, 03:01:22 pm »
May have tank, engine blank side cover/oil cover, barrell and odd finned clutch cover


45
Yamaha / Re: YZ360 pistons
« on: March 21, 2016, 02:57:22 pm »
email me id have the 360 and the 250s somewhere, can they be used ?

Pages: 1 2 [3] 4 5 ... 485