« previous next »
Pages: [1]   Go Down

Author Topic: Help to ID Yammy Forks.  (Read 1998 times)

0 Members and 1 Guest are viewing this topic.

mx250

  • Guest
Help to ID Yammy Forks.
« on: February 16, 2009, 10:08:24 am »
Can anyone positively ID these forks. I think they are IT175 - 36mm.

Logged

Offline Viper666

  • Legend
  • *****
  • Posts: 841
  • "Yes I bought THAT number plate" so sue me!
    • View Profile
    • Ballarat Rovers MCC
Re: Help to ID Yammy Forks.
« Reply #1 on: February 16, 2009, 11:33:44 am »
Without length measurements I am guessing YZ125D/E, IT175F and various DT125's & 175's. If they are original then they are probably IT175F but many parts are interchangable so if the original ones were rooted then YZ125D/E would bolt straight in but had air caps but may have been replaced.
Viper666
Logged
Thank the Lord for Melbourne Bitter, anti-inflamatory drugs & an understanding wife.
YZ80H, YZ100G, YZ125E, YZ125F, YZ125G, YZ250D, YZ250E, YZ250F, YZ250G, YZ250H, YZ400F, IT125G, IT250K & a, a, a,      CRF250X???????    

How the FUG did that sh*tbox Honda get in here?

Offline vandy010

  • Legend
  • *****
  • Posts: 1982
  • #789 MX125a BMCC Brisbane
    • View Profile
Re: Help to ID Yammy Forks.
« Reply #2 on: February 16, 2009, 11:50:05 am »
i think the DT125/175s have 32mm stauntions. so i'd count them out if yours are 36mm.
Logged
"flat bickie"

mx250

  • Guest
Re: Help to ID Yammy Forks.
« Reply #3 on: February 16, 2009, 12:21:21 pm »
Length 925mm extended and 725 compressed, approximate (within about 5mm) allowing for aftermarket caps.

From what I can make out, by appearance they could be E,F,G,or H. I'm assuming they have 200mm of travel. Does that help anyone to ID?
Logged

Offline LWC82PE

  • Superstar
  • ******
  • Posts: 6006
    • View Profile
    • PE motorcycles & SuzukiTS.com
Re: Help to ID Yammy Forks.
« Reply #4 on: February 16, 2009, 01:10:00 pm »
I am quite certain they are 79-81 TT 500 or 80-81 XT 500, with Goki air caps.
« Last Edit: February 16, 2009, 01:12:01 pm by LWC3077 »
Logged
Wanted - 1978 TS185 frame or frame&motor. Frame # TS1852-24007 up to TS1852-39022

mx250

  • Guest
Re: Help to ID Yammy Forks.
« Reply #5 on: February 16, 2009, 01:14:00 pm »
Quote from: LWC3077 on February 16, 2009, 01:10:00 pm
i reckon they are 79-81 TT 500 or 80-81 XT 500, with Goki air caps.
The Goki air caps is right but I don't think they're XT or TT because of the Headlight Holders which I believe are original.
Logged

Offline LWC82PE

  • Superstar
  • ******
  • Posts: 6006
    • View Profile
    • PE motorcycles & SuzukiTS.com
Re: Help to ID Yammy Forks.
« Reply #6 on: February 16, 2009, 01:22:25 pm »
Im not sure exact years but those forks were the same as on IT and TT/XT for a few years anyway. I think the XT headlight brackets were rubber mounted? did the early IT's have brackets like that?. just have to wait and see until a knowledgeable 500 owner such as CJ drops in. Ignoring the brackets i still think they are late model XT/TT
Logged
Wanted - 1978 TS185 frame or frame&motor. Frame # TS1852-24007 up to TS1852-39022

Offline jimg1au

  • Legend
  • *****
  • Posts: 3489
    • View Profile
Re: Help to ID Yammy Forks.
« Reply #7 on: February 16, 2009, 05:44:55 pm »
the headlight ears are off 1979 it400f same as the set i had on mine
cheers
Logged

Offline Nathan S

  • Superstar
  • ******
  • Posts: 7275
  • HEAVEN #818
    • View Profile
Re: Help to ID Yammy Forks.
« Reply #8 on: February 16, 2009, 10:10:27 pm »
NOT YZ125D/E. The web above the axle is too short.

Fork boots suggest IT175G.

Logged
The good thing about telling the truth is that you don't have to remember what you said.

mx250

  • Guest
Re: Help to ID Yammy Forks.
« Reply #9 on: February 16, 2009, 10:10:44 pm »
Quote from: jimg1au on February 16, 2009, 05:44:55 pm
the headlight ears are off 1979 it400f same as the set i had on mine
cheers
I would have thought the 'ears', and many other bits, would be common to all IT's. What size forks were the 400's? 36mm?
Logged

mx250

  • Guest
Re: Help to ID Yammy Forks.
« Reply #10 on: February 16, 2009, 10:15:55 pm »
Quote from: Nathan S on February 16, 2009, 10:10:27 pm
Fork boots suggest IT175G.
All IT's worn boots didn't they?
Logged

mx250

  • Guest
Re: Help to ID Yammy Forks.
« Reply #11 on: February 17, 2009, 06:00:05 am »

I think I found the answer, at approximately 200mm of travel, its probably off an 'f' (195mm). Whatcha reckon!!


Logged

Offline Nathan S

  • Superstar
  • ******
  • Posts: 7275
  • HEAVEN #818
    • View Profile
Re: Help to ID Yammy Forks.
« Reply #12 on: February 17, 2009, 08:23:23 am »
Quote from: mx250 on February 16, 2009, 10:15:55 pm
Quote from: Nathan S on February 16, 2009, 10:10:27 pm
Fork boots suggest IT175G.
All IT's worn boots didn't they?

Yes, but not all of the same style. IT175D/E had a lot less ribs - not sure about 175F, but I thought they were like 175D/E.
Logged
The good thing about telling the truth is that you don't have to remember what you said.

Offline JC

  • Legend
  • *****
  • Posts: 1245
    • View Profile
Re: Help to ID Yammy Forks.
« Reply #13 on: February 17, 2009, 11:30:21 am »
I tho't IT175D/E forks were 34mm OD? Was I wrong?
Logged
Pages: [1]   Go Up
« previous next »