« previous next »
Pages: [1]   Go Down

Author Topic: Engine "Running On"  (Read 1991 times)

0 Members and 1 Guest are viewing this topic.

Offline PCMAX

  • B-Grade
  • ***
  • Posts: 254
    • View Profile
Engine "Running On"
« on: July 05, 2014, 01:24:29 pm »
I have a CR125 that tends to run on a bit when I shut off the throttle. I've checked for leaks from the inlet boot, gaskets etc all OK there and the idle is good when stationary but out on the track it never seems to run back to idle when I close the throttle (even with the clutch in).
Could this be a sign of a worn needle jet/needle?
Logged
74 MX250A, 75 CR250, 82 CR125, 82 YZ250J, 84 XR250,

mainline

  • Guest
Re: Engine "Running On"
« Reply #1 on: July 05, 2014, 01:46:35 pm »
Assuming the throttle is actually snapping shut? Ie. The tube spins freely, cable isnt kinked or gummed up. Pilot/airscrew could be too lean
Logged

Offline Canam370

  • Legend
  • *****
  • Posts: 1608
    • View Profile
Re: Engine "Running On"
« Reply #2 on: July 05, 2014, 02:00:35 pm »
Sucking air somewhere.
Logged
WANTED. Canams;all models,complete or parts.SWM stuff too!

I'm THE Thread Killer - when I post a thread dies!

Offline Rookie#1

  • Legend
  • *****
  • Posts: 1744
  • JUST SHUDDUP AND RIDE IT!!!
    • View Profile
Re: Engine "Running On"
« Reply #3 on: July 05, 2014, 02:30:17 pm »
How long since you've replaced crank seals?? :-\
Logged
THE SEXMAX.....coming soon to an Evo race near you!!! Lining up right along side the soon to be released TEDMAX!!!


CHECK OUT THE NEW FACEBOOK PAGE FOR VERi. VINTAGE ENDURO RIDERS INCORPORATED.

.https://www.facebook.com/pages/VERi-Vinduro/169617676550236

Offline PCMAX

  • B-Grade
  • ***
  • Posts: 254
    • View Profile
Re: Engine "Running On"
« Reply #4 on: July 05, 2014, 02:36:48 pm »
Crank seals were new about 12 hrs of riding ago. the slide slams shut when the bikes stationary. The air screw is 1-1/2 turns out. Might try another carby.
Logged
74 MX250A, 75 CR250, 82 CR125, 82 YZ250J, 84 XR250,

Offline sleepy

  • Legend
  • *****
  • Posts: 805
    • View Profile
Re: Engine "Running On"
« Reply #5 on: July 05, 2014, 03:31:51 pm »
Turn the air screw almost all the way in and try it. Also make sure you don't have any leaks around the top of the carb. Seen one just recently that was mising the gasket from the top of the carb and boy did it run on.
Logged

Offline vmxrider

  • A-Grade
  • ****
  • Posts: 366
    • View Profile
Re: Engine "Running On"
« Reply #6 on: July 05, 2014, 05:06:32 pm »
A leak down tester might will help with diagnosis,
http://forum.ozvmx.com/index.php?topic=24254.msg237606#msg237606
Logged

Offline evo550

  • Legend
  • *****
  • Posts: 2435
    • View Profile
Re: Engine "Running On"
« Reply #7 on: July 06, 2014, 09:23:50 pm »
Have you fitted an aftermarket pipe?
Changes in Weather/temp can really effect jetting.
Logged

Offline Lozza

  • Legend
  • *****
  • Posts: 4206
    • View Profile
Re: Engine "Running On"
« Reply #8 on: July 06, 2014, 09:35:52 pm »
Pilot jet too small and/or slide cut away too big.......maybe the air leak
Logged
Jesus only loves two strokes
Pages: [1]   Go Up
« previous next »