Messages

16

CZ / Re: 981 Clutch oil seals and tank colour

« on: December 05, 2023, 07:35:57 am »

Thanks Tony. You are a champion.

Much appreciated.

I am in touch with my local bearing supplier and will change it to Viton etc.

Might look at that mod as well.

Kind regards

Pete

17

CZ / 981 Clutch oil seals and tank colour and JETS

« on: December 01, 2023, 10:39:58 am »

Hi Gents,

Had the 1973 380 going with new Vape Ignition. Brilliant.

New issue is oil leak behind the dry clutch.

Question - what are the sizes and or id numbers for the seal (and type maybe)  and oring/s   ?  Possible 50 x 65 x 8 mm but not sure if single or double lip, or spring etc if it matters.

Question - size of the Oring on the kick starter shaft ?

Question - I want to paint a steel tank in the original '73 Blue colour. Any idea what the colour code is or close to it?

Many thanks once again

Pete

18

CZ / Re: 1973 PARTS BOOK

« on: November 03, 2023, 06:27:38 pm »

Tony 27,

The document you supplied has been the biggest help ever. Much appreciated. the 380 is moving along very nicely. Parts arrived from CZ Stuff in the UK very well. Looking forward to 2024 with Hunter Classic VMX. Pete

19

CZ / Re: 1973 PARTS BOOK

« on: October 06, 2023, 09:08:24 am »

Thanks for the help guys. I did print some stuff off years ago for the 250 from CZ madness but it went with the bike. 

Looking for what the std front and rear sprockets were for the '73  380. Currently has 13/52.  Running off the book you kindly put up Tony that looks like standard for the 380.  Thanks so much.
Cheers

Pete

20

Maico / 1977 FORKS HOW TO GET DAMPER RODS APART

« on: September 07, 2023, 06:28:39 am »

Hi Guys,

            How do I get the damper rods apart on my AW?  I want to add PD valves but need to reduce the preload. I'm told that we need to shorten the alloy spacer that sits within the damper rod. I take it I need to get the alloy screw/nut cap that screws up into the fork leg. But it is on hard.

If anyone has fitted PD valves be good to get their views on the how too and oil specs etc.

Many thanks

Pete

21

CZ / 1973 PARTS BOOK

« on: June 01, 2023, 10:56:17 am »

Hi Guys,

Did a 73 250 a few years ago. Now doing a 73 380. The 250 has gone to a new owner.

I am looking for the parts book to check for missing or odd bits on the 380.

Is it possible to down load an electronic copy from somewhere?

Kind regards
Pete in Wollongong

22

Kawasaki / Re: Decals for the KLX tank and plates

« on: July 17, 2021, 11:01:39 am »

Thank you very much Cyclegod. Appreciate the help.

Going to give it one more going over and put it up for sale.

Many thanks

Pete

23

Kawasaki / Decals for the KLX tank and plates

« on: July 13, 2021, 06:17:59 pm »

Hi Boys,  Can someone point me in the right direction of good quality tank and 250 decals for the KLX 1980.

Kind regards

Pete in Wollongong

24

Kawasaki / Re: KLX SWINGARM CHAIN BUFFER/GUARD NEEDED - Now 3D printed

« on: August 09, 2020, 06:01:52 pm »

Guys all sorted and now Greg Tow from the Heaven club is 3 D  printing new ones.

Pete

25

Yamaha / Re: IT 250 K AIR FILTER ASSEMBLY ?

« on: July 25, 2020, 08:23:36 am »

Thanks Momus and Woody,

Victor from Heaven called me yesterday. He has IT and YZ 250's and said the metal plate goes up against the plastic cage. I looked at the sandwich idea but soon realised the stiff metal plate would not conform to the airbox shape. And when I think of it I can't remember ever seeing an air filter that didn't butt up against an air box to make a good seal.

Thanks for the help

Pete

26

Yamaha / IT 250 K AIR FILTER ASSEMBLY ?

« on: July 24, 2020, 01:20:38 pm »

Guys I need advice on fitting up the air filter on a 1983 IT 250 K.

It has a cage with 2 x 6mm threaded bolts attached to it, the foam filter and the bit I have the problem with a pressed metal ring the same shape as filter cage.

Where does that pressed metal bit go?

ie Onto the cage then put the filter over both OR put the filter on the cage then the metal bit over the to, basically sandwiching the foam filter between the cage and the pressed metal thing.

I have asked two Yamaha IT YZ owners close to me and neither had any idea.

Thanks in advance

Pete

27

Kawasaki / Re: KLX 250 Standard Needle or replacement

« on: June 10, 2019, 06:44:28 am »

Hi John,

Not sure as yet. But I know it's not the standard one. Was planning get hold of the standard one and do it all in one go

Cheers Pete

28

Kawasaki / KLX 250 Standard Needle or replacement

« on: June 09, 2019, 03:13:37 pm »

Afternoon guys,

KLX used at Braidwood VTR the other week pinged due to lean neeedle.

Owners manual says it should be a a Mikuni  Jet Needle  6H2-2.

Not whats in it. Had a look on Mukunioz but couldn't find it.  I heard it might be a `special' .

What can be used as a standard replacement needle?

Kind regards

Pete

29

Kawasaki / Re: KLX SWINGARM CHAIN BUFFER/GUARD NEEDED

« on: May 04, 2019, 07:28:54 pm »

Yes Geoff. Back together and running ready for the next Braidwood

30

Kawasaki / Re: KLX SWINGARM CHAIN BUFFER/GUARD NEEDED

« on: March 23, 2019, 07:18:22 pm »

Ok Thanks GMC and Cloggy. I will chase it up now

Pete