Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - mick25

Pages: [1] 2 3 ... 6
1
Wanted / Wanted Yamaha rear hub TT500 etc
« on: July 05, 2020, 08:27:11 AM »
Chasing a good Yamaha rear hub TT500 but lots of other Yamaha models run the same hub YZ etc

2
Tech Talk / Bearing grades
« on: February 12, 2020, 08:31:20 PM »
Going back some years , I remember someone asking what’s the best option for bottom end bearings from bearing shops was it C2 ,C3 or C4 ?

3
Wanted / Wanted XR500 81/82 top de comp cable
« on: April 02, 2017, 07:17:22 PM »
I'm chasing a good decompression cable from a XR500 1981/82  that Gos from the head to handle bar lever type .
Ebay or other cable supplies don't keep them , if no
Luck here I will get one made..

4
KTM / Ktm 504 1983 Mxc or not ?
« on: March 24, 2017, 06:54:30 PM »
I can get my hands on a ktm 504 Mxc 1983 rotax if I want but need some advise or a push.
I've done some web research and found only good stuff about them they are rear only 40 came to oz one thing that makes it more worth it.
I Have read engine parts can be sourced from a few places in the states and in England but not cheap.
The rotax engines are popular in the states in flat track racing and Ron wood is the go to man over there .
They have a rubber belt instead of a timing chain but if it replaced when needed no
Probs.
I found a couple of places that still do
Plastics etc for it .
And the Mxc model has bigger forks , diffrent cam and crank than the GS model.
But the specs on the net says it weighs 156kg ouch not sure if this is right  ???
I still think it would be the best pre 90 four stroke .
What do you guys think , buy it or not ? Then I wouldn't mind a CR250 87 or 88 ? :o

5
Tech Talk / Ohlins shock eyelit remover
« on: September 08, 2016, 07:13:27 PM »
Hi guys
I want to put the shortest bottom eyelits on my piggy back Ohlins to make them shorter.
I came up with a idea to remove them with out damaging the chrome shalf ,
I have a peice of alloy square 25mm x 25mm I drilled a hole in the centre of it the same size as the shock shalf then I cut it in half through the centre of the hole so I could put one peice eather side of the shock shalf right at the end of the shalf then clamp it in a vice to stop the shalf Turning while removing the eyelit is this how the pros do it ?
I just don't Want to damage the chrome on the shalf but I will be doing this right at the end of the shalf where it's not going to travel into the shock body .
Or should I just post them to Steve cramer  or bk on this forum ?



 

6
Trying to get a frame from Sanctuary point  nsw or from Nowra nsw  to dargle in nsw heavens next bike meet this weekend  :o
Can pay by beer or smokes or gas . ;D
 

7
Wanted / Wanted dr500 or sp500 chain adjusters
« on: July 01, 2016, 03:59:17 PM »
In need of some dr500 or sp500 chain adjusters to suilt the steel swingarms
If any one has six of  :o that would be great .
There's some on eBay in the states but with postage and the dollar exchange its works out a lot .

8
Wanted / Wanted 1976 xt500 bits
« on: May 04, 2016, 08:40:28 PM »
A mate is chasing some 1976 xt500c bits .
He's After Org rear shockers he said they are shorter than other model xt,tt500 models.
Standard Tt,xt500 lengths are 365mm long so must be a tad shorter than this to suit the xt500c .
And he's after the rear heat shield that's towards the end of the org exhaust system.
He's trying to find these bits in Australia rather than Ebay in the states with the dollar exchange and postage costs .
Thanks mick.


9
General Discussion / Yamaha 500 thumper round up
« on: June 28, 2015, 07:57:54 AM »
There's a Yamaha 500 thumper round up for sr,xt,tt500 bikes for the first time here.
Its starting at 11am 26 September 2015 at the Khartoum hotel Kitchener 5 mins from cessnock 2325 nsw and 45mins drive from newcastle .

I have seen the flyer and throught of posting the info here for other 500 nuts .
There's a sausage sizzle and other interesting things to do and see .
I used to live there it was a real thumper stomping ground for the yammie thumpers in the ninetys
And there's still a lot of thumpers around this area.
And there's plenty of bush over the road from the pub for circuit work  :o

10
Vintage Track / Front tire choice for Barleigh ranch flat track
« on: January 29, 2015, 08:31:14 PM »
Just seeing if anyone is going to give the secrets away on the flat track front tire choices,
For barleigh ranch.
For the vintage bikes .
I am new to this sliding thing so go easy , thanks mick

11
Tech Talk / KX125,250 A4 78 swingarm length
« on: January 04, 2015, 02:30:25 PM »
Anyone got one to measure centre of pivot shalf to centre of axle slot , has to be A4 model not 79A5 as they are longer. thanks mick

12
Wanted / Wanted 1983 KDX 250 stator
« on: September 06, 2014, 02:18:20 PM »
Posting for a mate 1983 KDX 250 stator , or if someone knows if another Kawasaki stator is the same.
     Thanks Mick

13
Bike Transport / Gympie QLD to sunshine coast or brizzy
« on: May 11, 2014, 07:36:27 PM »
Just seeing if someone is passing by Gympie way QLD and could pick a bike up , and drop it off at some ones place on the forum in brizzy or the sunshine coast , untill I work out getting it down Newcastle way. for beer or smokes or cash  ;D
Thanks mick.

15
Wanted / Wanted PE400 1980 exhaust system
« on: April 18, 2014, 06:58:06 PM »
A Mates chasing a PE400 1980 exhaust system , hope someone has a lazy one sitting around ;)

Pages: [1] 2 3 ... 6