Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - rocketfrog

Pages: [1] 2 3 ... 5
1
For Sale / YZ125H/IT250/IT465H NOS Fork inner tube
« on: August 04, 2020, 01:51:32 pm »
I have for sale a 4V2-23110-L0-00 INNER TUBE 1 NOS $150 (I only have the one). International seller sent me the the incorrect part and I cannot use it.

2
Wanted / 1979 yz250 pipe buy or trade for NOS Plastic
« on: April 07, 2020, 09:46:52 am »
Has any a YZ250F Exhaust system for sale? I would prefer a good stock pipe but an aftermarket might be acceptable depending on condition/style. I have cash or a set of NOS Side Covers/Airbox cover for the 1979 YZ400/250 in clean white to trade for a mint/NOS stock exhaust system.

3
Honda / Honda CR125 Top end interchangeability
« on: January 22, 2019, 11:36:26 am »
Guys/Gals, I would normally search sites such as partzilla for interchangeable part numbers to seek the answer to the following question myself, however, my research has come up short.

Has anyone knowledge of a known Bolt on top end substitute for a 1992 CR125. For example do 1991 - 1993 use a cylinder assembly (inc power valves etc;) that will bolt up and work on the 1992 CR125 Bottom end?

I have seen ads for cylinders that state "fits 1991-1995 CR125" is there truth to this or not?

Usually I would check which parts are used on other year models and make a judgement based on say base gasket interchangeability indicates the same stud pattern on models using the same gasket for example, Piston interchangeability suggest the bore and stroke are the same one year to the next and so on.

In this case the part is discontinued and no supplementary information is available, so I need first hand Honda expert experience before I pony up for a barrel/top end that will not work with what I have.

Cheers

4
General Discussion / Calling Anthony Gunter
« on: July 27, 2017, 02:42:52 pm »
Does any one have the contact details for Anthony Gunter?

5
Wanted / YZ125T Frame section
« on: July 26, 2017, 12:04:10 pm »
Does any one have a donor frame they would cut a section from for a repair?

The rear subframe has been cut to make a removeable strut similar to the 89 onwards YZ's. But it is a bad job and the owner would like to return to the stock configuration.

I am not sure if it is the RH or LH side which is required as yet, but if there is a willing donor it will save a lot of work.

Thanks in advance.

6
Wanted / kx250 Bits needed
« on: February 16, 2017, 07:37:11 pm »
Can anyone help with an exhaust system, and radiator grilles/radiators and front number plate and mudguards for a 1990 KX250. Most 1990 to 1993 look like they will fit or could be made to fit.

Scraped, scratched or faded is OK.

Looking for good usable bits or parts which could be repaired within reason, ie exhaust with a few dings wont be a problem if you catch my drift.

Just want bush basher quality- closer to Ipswich, Qld the better.

Cheers Jason

7
Wanted / YZ250/465 H swing arm
« on: January 07, 2017, 08:51:46 pm »
I need a 1981 YZ250 or YZ465 H swing arm in Very Good Condition. Bare arm required, no need for chain guides or bearings, just a good straight arm with out major chain rash.

I have plenty of decent  YZ250G/H parts to trade or good cash paid for the right part.

Note that it must be the longer 1981 YZ arm with the larger axle slots.

Cheers

8
Bike Transport / Brisbane - Cairns - Brisbane
« on: January 05, 2017, 12:37:59 pm »
Limited space from Brisbane via Kingaroy to Cairns (good for smaller bits like components such as wheels, engines etc.)

Empty on the way back for a few bikes.

Depart Bris NLT Mon 6 Feb and return (depart Cairns) NLT 8 Feb.

 pm if your keen.

Happy New Year  :)

9
eBay Finds / REVERSE ENGINEERING?
« on: August 23, 2016, 09:06:16 pm »
I usually see the guy who takes an ag bike and turns it into a racer, but this bloke had other ideas for his project.........

http://www.gumtree.com.au/s-ad/raceview/motorcycles/suzuki-offroad-bike/1121507535

10
Wanted / yz80e parts
« on: July 26, 2016, 10:48:06 am »
Any one with a YZ80E/F airbox and side covers they want to sell?

Please dont contact me if you have parts that you dont want to sell or might sell or if your on the fence about whether to sell or not.

Cheers

11
Competition / pre 95
« on: July 09, 2016, 12:54:47 pm »
probably covered before, but is there any class for a 1995 bike? can any one send me a link to a board that discussed this question or if anyone knows off hand please let me know.

12
Wanted / 1996 YZ250 RAD SCOOPS
« on: June 17, 2016, 11:55:30 am »
Has any one got some decent plastics for a 1996 YZ250 (I believe 125 is the same) please.

Mainly I need some shrouds and the radiator grills and a rear gaurd. Sing out if you can help.

Cheers Jason

13
For Sale / YZ80E
« on: October 28, 2015, 03:16:28 pm »
Is there any one keen on a YZ80E project? I have 90% of a core bike with DG Swinger and head but not much motivation to cobble it all together. I would prefer to discuss a deal via the phone and send pics to individuals on request, message me your number if your keen. I want $1000 for the lot as is where is, or would be keen on a swap for a YZ80G in similar condition.

14
Wanted / YZ80E Tank and pipe
« on: October 26, 2015, 12:20:31 pm »
as the title suggests, I would like to track down a tank and pipe for a 78 yz80. It actually needs a proper airbox and side covers as well but the pipe and tank are the show stoppers, the pod filter will work for the moment, any leads guys?

15
Wanted / bike transport
« on: October 12, 2015, 09:59:35 am »
Can anyone help with bike transport from Innisfail North Qld to Brisbane? Perhaps if there is a door to door courier any can recommend on this route please give me a shout out.

Pages: [1] 2 3 ... 5