Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - D project

Pages: [1] 2 3 ... 5
1
Kawasaki / KX Green paint code
« on: January 31, 2017, 01:25:53 pm »
Jus bought a KX80B resto project,anyone have an accurate paint code to match the tank green.

2
Wanted / YZ125 G/H airbox cover
« on: December 23, 2016, 01:00:34 pm »
Anyone have an airbox side cover and the metal bar that it secures to,to suit a 125 G/H

3
Wanted / YZ125G/H swingarm
« on: November 02, 2016, 01:25:24 pm »
Anyone have a swingarm arm to suit. Also after a rear brake cable.

4
Yamaha / YZ 125G/H
« on: October 28, 2016, 02:05:36 pm »
Just starting a resto on a 125G. How much is interchangeable between the G and H.
I'm chasing a few bits eg swing arm, air of,rear wheel,shock mudflap.
These are a straightforward swap?

5
Wanted / RM throttle assembly
« on: June 22, 2016, 12:50:18 pm »
Anyone have a comple assembly to suit 89 RM. I think anything 83 onwards are pretty much the same?

6
Tech Talk / Tyre fitting
« on: April 28, 2016, 01:24:22 pm »
I always seem to have difficulty seating tires beads on rims.
Any tips or what lube do people use. I've just been using the old standard "soapy water"!

7
Tech Talk / Tyre life
« on: October 23, 2015, 12:44:23 pm »
I've got a few MX tyres that are a couple of years old but the tread still ok.
What's the rubber life span,do they loose there grip/performance and how do you tell?

8
Tech Talk / Crank seals
« on: February 02, 2015, 11:13:38 am »
After forgetting which way my crankseal on the clutch side goes in, I'm confused.
Does it really matter which way it's installed? One side of the seal is closed with a flat face the other is open with the wire spring retainer. It's a double lip seal on a 89 RM250. Going by the drawing/diagram in the Suzuki manual it looks to have the open side facing the transmission. Looking at cases for sale on eBay some have the flat side facing out to the clutch, but the majority with the open side out. Flywheel side allways has the spring on the inside. Is it only when the seals are worn that they can suck air and oil in?

9
Tech Talk / 18 V 19 rear wheels?
« on: November 14, 2014, 01:07:50 pm »
Another one of my questions that has been bugging me ::).
Whith dunlop not making their MX32 in an 18" rear is there any benefit in going from an 18" to 19" rear wheel? How does it affect gearing and suspension?

10
Tech Talk / Nikasil V re sleeve?
« on: November 09, 2014, 08:51:06 am »
What's people's preference? What sort of lifespan do you get out of a nikasil bore? Or is it better/cheaper to just put a new sleeve in and re bore when required?

11
Suzuki / RM125N jetting specs
« on: November 07, 2014, 01:12:08 pm »
Anyone know what the standard jetting specs are supposed to be for the 125N?
My mate has bought a new carb and hasn't got an original manual to suit.
Suzuki doesn't list the needle or needle jet only the part numbers :-\

12
For Sale / RM465/500 DG Pipe and muffler
« on: October 21, 2014, 01:36:09 pm »
Got a DG Pipe and muffler for sale. Had a crack near the mounting bracket which has been repaired.
Other wise in good condition, probably about 6 hours use.
$200 plus postage.

13
General Discussion / Ohlins shock parts
« on: October 20, 2014, 12:45:37 pm »
Anyone know where I can buy some new parts to rebuild an ohlins single shock.
After a new seal head, piston band, etc.
Thanks.

14
For Sale / 81/82 RM250/465 Front rim.
« on: October 15, 2014, 12:58:20 pm »
Got a couple of front rims and backing plates to suit 81/82 250/465.
One rim is cracking at the join the other has a ding in it.
So only good for the hubs I suppose. $30 each plus postage?

15
For Sale / 83 RM250/500 front end.
« on: October 14, 2014, 09:04:42 pm »
Got a set of forks,triple clamps, brake plate which is 84, wheel,axle and near new brake cable.
Like to sell as a complete set up. Forks are in good condition overall with good chrome and lower legs.
$425.

Pages: [1] 2 3 ... 5