Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - YZ250H

Pages: [1] 2 3 ... 10
1
Bike Transport / Pick up and Store in South Australia
« on: July 08, 2019, 07:40:57 am »
Hi Guys,

Our old mate Mainline, or PaulOs has (stupidly  :o ) let his ozvmx membership lapse for some reason.  He is looking for someone to pick up and store (for a short time) a YZ125 from Southa Australia.

Is anyone able to help please ?

Cheers

2
Wanted / YZ 125G Barrel
« on: February 21, 2017, 01:47:26 pm »
Hi Guys,

My brother in law is desperately seeking a 125G barrel as the one he has at the moment has a broken clutch cable holder and a mangled top surface where someone has taken to it with god knows what.  Can probably be fixed with a lot of effort, but looking for something a bit easier first.

It's his first VMXer so he's keen as mustard to get it going  ;D ;D

Anything out there ?

3
Honda / 74 CR125M Bottom end bearing and seal sizes
« on: September 01, 2016, 12:25:23 pm »
Hey Guys,

Does anyone happen to have a list of the bearing and seal sizes for the bottom end of a CR125M 1974.  Looking to get the bearings before I pull the thing apart to save some time.

All help greatly appreciated as always.

Cheers

4
Wanted / Anyone have a 1974 CR125 Manifold that fits Mikuni Carb please ?
« on: May 26, 2016, 08:49:57 am »
Desperately seeking in time for classic dirt.

At least I haven't left it until the last minute  ::) ::)

5
Honda / Where would I buy CR125M swing arm bushes please
« on: July 07, 2015, 03:40:59 pm »
Found some on an American website but $180 US  :o :o

I figure I should be able to do better than that  :-\

6
Wanted / Wanted to borrow - YZ250H Crank
« on: May 04, 2015, 07:26:17 am »
Adapting another flywheel to the crank and need to get some machining done.  Would prefer not to pull my engine apart.

Happy to provide beers, first born or whatever is needed.

Anyone ??

7
Yamaha / YZ 250H Ignition Advance Curves
« on: April 02, 2015, 09:05:36 am »
Hey Guys,

I'm doing some research on HPI ignitions and I want to compare the advance curve they provide with the standard Yamaha Curve.

Is anyone able to help ?  If the HPI ones are any good you can get the entire ignition for the same price as getting a coil rewound  :o :o

Thanks in advance for any assistance given.

Cheers

8
General Discussion / Are these legal for Pre 75 ?
« on: March 11, 2015, 01:21:37 pm »
OK, I know they are cheap, but they are all the current budget allows and the current ones are cactus giving my back a hard time  :o

For my 75 CR125

http://www.ebay.com.au/itm/141474951512?_trksid=p2060778.m1438.l2649&ssPageName=STRK%3AMEBIDX%3AIT

I'm not even a threat to second last in races so ....

Thoughts please

9
Twinshock Trials / TY 250 A Exhaust Tab on Rear of Frame
« on: March 06, 2015, 02:56:06 pm »
Any chance someone could post a picture of the exhaust mounting arrangement at the rear of the frame ?

Someone has butchered mine.  Otherwise the frame is good and ready to be blasted  8)

Thanks in advance guys

10
Yamaha / YZH frame rust prevention
« on: February 06, 2015, 12:00:17 pm »
After a recent horrifying experience I'm wondering how I might protect my frames from rusting out like this one.

[/URL]

Any ideas from the brains trust ?


11
Wanted / YZ465H Frame
« on: February 05, 2015, 09:50:21 am »
I know  ::)

But mine is rusted out in the gusset.  Just putting the feelers out for what might be available and how much it might cost.

Weighing up my options for repair or replacement.

PM me or a reply here is fine too.

12
Wanted / TY 250ABCD / 175BCD Front Backing plate
« on: January 30, 2015, 08:39:56 am »
Has Speedo drive slot which I intend to use.  The old one has totally disintegrated.

I still have all the speedo workings, so the plate by itself is OK.

Thanks in advance for any help.

13
Honda / 1974 CR125M Rear Exhaust Hanger Alternative or Lead on Original
« on: December 12, 2014, 10:40:13 am »
Hi Guys,

Just wondering if anyone has an alternative to the standard rear exhaust hanger bracket.  The original one is missing from my bike and the previous owner created a dodgy alternative that has since broken.  Even pictures of what it is supposed to look like would help a lot - I may be able to make something.  I've got  GMC pipe on mine, but I'm pretty sure Geoff would have made it to suit the standard bracket.  What ever it is needs to be rubber mounted - because a solid connection definitely doesn't work.

Thanks in advance for your help fellas.


14
Yamaha / What's a decent aftermarket gear lever for a YZ465 ?
« on: May 02, 2014, 10:46:49 am »
The one I have is poop

15
Tech Talk / Frame Welder in Brisbane
« on: April 30, 2014, 01:16:49 pm »
My 465 has a rusted (under powdercoating) and now cracked Gusset behind the head stem.  Can anyone recommend someone in Brisbane to fix it for me please ?

At the very worst I can remove the old one and shape a new one, so even somone that can weld neatly might do the trick  :-\

Cheers

Pages: [1] 2 3 ... 10