Messages

1

Wanted / Yamaha mx250a parts

« on: August 03, 2019, 11:21:02 am »

Just finishing of restoring my 1974 mx250 and chassing some missing parts.

Air box and intake pipe
Left hand foot peg bracket and peg
Cdi bracket
Clutch basket

Maybe some other small parts if anyone has anything let me know
Thanks

2

Wanted / Re: Honda CR250M 1973-74 Parts Wanted

« on: May 21, 2016, 12:54:08 am »

Thanks Bazza,Wasn't sure if they had steel or Alloy.Hopefully Now,I'll pick some nice Honda XL rims
up without the cracks and corrosion.Saw one on Gumtree looked OK.
Thanks BigK , I'm keen on your forks, axle and plastics.
Ross asked why not go aftermarket, I found you can't get the correct
Reproduction colour in the plastic and have to paint to match.So if yours are
Repairable I'm keen.
I do have a set of fork tubes I was told they're Cr250m 73/74.They have the 5 rings turned into the top
But they seem a little long.The tubes measure 578mm long.They're out of the slider thats the shaft itself top to bottom.
And they're 35mm diameter as they're meant to be.
Thanks guys any info would help.

 

3

Wanted / Honda CR250M 1973-74 Parts Wanted

« on: May 19, 2016, 12:55:58 am »

Looking for Complete wheels or seperate rims or hubs
To build a nice set of wheels with stainless spokes.
Also looking for Forks,Plastics and rear axle.
Thanks

4

Wanted / Re: Wanted--Suzuki RH250 1974--

« on: February 24, 2016, 04:56:46 pm »

Yeap that right ,RH73 or RH74
Cool Thanks

5

Wanted / Wanted--Suzuki RH250 1974--

« on: February 23, 2016, 11:51:27 pm »

I know it's a long shot but have to give it a go.
If you know of or have an RH 250 73 or 74 and want
To let someone else enjoy it.Please Contact me.
I do have a nice RH 250 1975 in mid restoration and it seems
a bit lonely without its older brother to hang out with.

Basket cases,Mid restos,I'm still interested
Thanks

6

Wanted / Re: TM125

« on: February 18, 2016, 10:30:05 pm »

I been lookin for a TM seat locally for a year.
Ended up getting a RM250/125 1976/78 seat.
You get a plastic seat base.That dont rust or crack
Like the steel base.You do have to modify the rear mounts a
little or make new ones from alloy as I did.The  cosmetic difference
is the Kick-up at the rear of the seat,I think it looks good.And the cover.

7

For Sale / Re: PVL ignition suit CR125M 1974/78 $450

« on: February 17, 2016, 09:42:02 pm »

Yeah it physically fits yes ,I read though,
The CR250m is uses a fixed points system.Where the CR125M uses the retard and advanced timing provided by its CDI map. The CR250M's port timing and low compression are not designed for this ignition CDI mapping.Yes it would work but I would lose power towards the top end revs as it advances.Then I thought the 75 CR250M1 has CDI ,but read that it had different port timing and higher compression to suit its new CDI ignition in 1975. So I wanted the correct CDI map.I wish it wasn't that way I would bolt it on now.
So when I sell it I'll buy another.If ya can point out my research is wrong, It would save me some headaches

8

For Sale / PVL ignition suit CR125M 1974/78 $450

« on: February 17, 2016, 07:35:22 pm »

Penton Racing Products
PVL Ignition Part number #70411
New in box
Came with my CR250m
But is the wrong one
Suits Cr125M 1974/78
        CR125R 1979-85
        MR175  1975-77

9

Wanted / YAMAHA DT2MX PARTS

« on: February 05, 2016, 12:30:40 am »

G'day
    Just picked up a DT2MX.unfortunately it's missing
A few vital parts to make her nice again.
WISH LIST
 DT2MX tank or RT2MX same parts
Front and rear guards
Both side plates.
Also keen on barrels,engines,engine parts
Thanks