1
For Sale / SOLD - Enclosed 3 Bike Trailer
« on: May 08, 2016, 04:40:57 pm »
SOLD
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1] 2
2
For Sale / YZ125L 1984 For Sale
« on: March 08, 2016, 03:53:21 pm »
Hi All,
For anyone who is after a great Pre 85 125, my 1984 YZ125L is for sale on Gumtree.
$4,000k for fully restored and sorted race ready YZ. I haven't ridden it since the start of the 2014 Heaven season.
So now it's time for it to go to someone who will get the use out of it rather than sitting in the shed.
Cheers
Pete F
Heaven #179
0418 287 310
For anyone who is after a great Pre 85 125, my 1984 YZ125L is for sale on Gumtree.
$4,000k for fully restored and sorted race ready YZ. I haven't ridden it since the start of the 2014 Heaven season.
So now it's time for it to go to someone who will get the use out of it rather than sitting in the shed.
Cheers
Pete F
Heaven #179
0418 287 310
5
For Sale / Re: 1989 Honda CR250 RK
« on: June 30, 2015, 02:28:12 pm »
Scotty it's got your name written all over it. I can just see that big bushy beard of years flapping off the back!!
11
For Sale / 1989 Honda CR250 RK - SOLD
« on: November 10, 2014, 11:52:44 am »
For sale is my 1989 CR250 RK.
7.5hrs run time since full engine rebuild and restoration. The 7.5hrs has comprised 5 Singleton MC ride days, 1 Heaven Saturday practice at Bulladelah. I ran it in the Evo Challenges in 2012/13 at Lake Glenbawn when we had the combined Heaven/Pre 89 Club events (which convinced me to stick with 125's before I hurt myself!).
The restoration included:
Full top and bottom end rebuild by Steve Baylis in Bathurst - piston, rings, rod, top and bottom end bearings and seals.
Suspension by Terry Hay at Shock Treatment, Walacia.
Complete replacement of all frame and suspension linkage bearings and seals
New brake pads, chain (RK Gold), sprockets, tyres (Metzeler MC5's front and rear) - all now about 75%.
New Unifilter, grips (Progrip 801), chain roller (genuine Honda).
Overall the pipe is in good condition. One weld near the header to repair a crack and only a couple of minor dints. Muffler is a FMF Turbine Core.
Cosmetically the bike is pretty much original and in very good condition. Tank, shrouds, side plates, seat are all in very good condition. Rear fender is badly scraped as per photo.
Now $5,000.
Peter
Heaven #179
0418 287 310
7.5hrs run time since full engine rebuild and restoration. The 7.5hrs has comprised 5 Singleton MC ride days, 1 Heaven Saturday practice at Bulladelah. I ran it in the Evo Challenges in 2012/13 at Lake Glenbawn when we had the combined Heaven/Pre 89 Club events (which convinced me to stick with 125's before I hurt myself!).
The restoration included:
Full top and bottom end rebuild by Steve Baylis in Bathurst - piston, rings, rod, top and bottom end bearings and seals.
Suspension by Terry Hay at Shock Treatment, Walacia.
Complete replacement of all frame and suspension linkage bearings and seals
New brake pads, chain (RK Gold), sprockets, tyres (Metzeler MC5's front and rear) - all now about 75%.
New Unifilter, grips (Progrip 801), chain roller (genuine Honda).
Overall the pipe is in good condition. One weld near the header to repair a crack and only a couple of minor dints. Muffler is a FMF Turbine Core.
Cosmetically the bike is pretty much original and in very good condition. Tank, shrouds, side plates, seat are all in very good condition. Rear fender is badly scraped as per photo.
Now $5,000.
Peter
Heaven #179
0418 287 310
12
For Sale / YZ125H - 1981 - parts - SOLD
« on: August 26, 2014, 12:28:43 pm »
A clean out of my shed has uncovered the following YH125H 1981 parts which I salvaged off a wreck a few years ago that I no longer need (originally I had the idea of using the swing arm, mono shock, triple clamps and forks on my 1980 "G").
Complete motor including kick starter -4V2- haven't pulled down so internals unknown. At very least should be able to salvage some parts. Cases are fine.
Triple clamps - look to be in reasonably good order with radiator port intact.
Set of 38mm forks to suit the triple clamps. Rust up top near triple clamps but sliding surface seems ok.
Monoshock
Swing arm
Frame rubber that goes under seat near where rear mudguard bolts on
Rear axle and chain adjusters
Assorted nuts and bolts.
$100 the lot. Pick up Chatswood, Sydney.
YZ125G owners may also be interested as the swing arm, mono shock and triple clams will fit on a "G" giving bigger front forks and slightly longer wheel base.
Cheers
Peter
0418287310
Complete motor including kick starter -4V2- haven't pulled down so internals unknown. At very least should be able to salvage some parts. Cases are fine.
Triple clamps - look to be in reasonably good order with radiator port intact.
Set of 38mm forks to suit the triple clamps. Rust up top near triple clamps but sliding surface seems ok.
Monoshock
Swing arm
Frame rubber that goes under seat near where rear mudguard bolts on
Rear axle and chain adjusters
Assorted nuts and bolts.
$100 the lot. Pick up Chatswood, Sydney.
YZ125G owners may also be interested as the swing arm, mono shock and triple clams will fit on a "G" giving bigger front forks and slightly longer wheel base.
Cheers
Peter
0418287310
13
For Sale / For Sale YZ125G 1980
« on: August 25, 2014, 04:28:58 pm »
Still available if anyone is interested. Cheers pete
14
Tech Talk / CR250 89 front brake calliper and disc
« on: May 22, 2014, 08:31:34 am »
Hi All,
I'm looking to uprate the rotor, calliper and master cylinder on my CR250 1989 (the first of the upside down fork models). Ie fit a rotor, calliper and master cylinder off a latter model. Does anyone know if a more modern Honda calliper will fit on the fork mounts on the 89 and if so up to what date. I'm thinking that the mounts should be fairly standard up through the years? Thanks Pete
I'm looking to uprate the rotor, calliper and master cylinder on my CR250 1989 (the first of the upside down fork models). Ie fit a rotor, calliper and master cylinder off a latter model. Does anyone know if a more modern Honda calliper will fit on the fork mounts on the 89 and if so up to what date. I'm thinking that the mounts should be fairly standard up through the years? Thanks Pete
15
For Sale / For Sale YZ125G 1980 - SOLD
« on: May 20, 2014, 03:38:16 pm »
Up for sale is my YZ125G 1980.
0.5 hours since top end refresh with Woosner piston and ring
19 hours since original ground up restoration and top and bottom end rebuild with all new bearings, seals, cables etc
Features include:
New Eceed rims and stainless spokes by Chris Squires at Spoked Wheel Repairs
Front Fork upgrade with PD valves and heavier springs by Nick Dole at Teknik Motorsport
Rear shock upgrade with Double Taper Progressive Spring and Olins shaft and valve kit by Nick Dole at Teknik Motorsport
Gunner Gasser throttle and cable
Maeler front fender
New genuine Yamaha ignition coil
Boyesen Power reeds
Dunlop MX51 Front, Metzeler MC5 rear
Vintage Iron alloy muffler
New genuine top tripple clamp
Wide alloy footpegs
DC side plates (comes with the original side plates and yellow tank)
Priced at $3,250.
Peter 0418287310
Heaven No 179
0.5 hours since top end refresh with Woosner piston and ring
19 hours since original ground up restoration and top and bottom end rebuild with all new bearings, seals, cables etc
Features include:
New Eceed rims and stainless spokes by Chris Squires at Spoked Wheel Repairs
Front Fork upgrade with PD valves and heavier springs by Nick Dole at Teknik Motorsport
Rear shock upgrade with Double Taper Progressive Spring and Olins shaft and valve kit by Nick Dole at Teknik Motorsport
Gunner Gasser throttle and cable
Maeler front fender
New genuine Yamaha ignition coil
Boyesen Power reeds
Dunlop MX51 Front, Metzeler MC5 rear
Vintage Iron alloy muffler
New genuine top tripple clamp
Wide alloy footpegs
DC side plates (comes with the original side plates and yellow tank)
Priced at $3,250.
Peter 0418287310
Heaven No 179
Pages: [1] 2