Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Davy123

Pages: [1] 2 3 ... 7
1
Yamaha / Re: DT2MX
« on: October 24, 2019, 05:54:57 am »
iain ... cheers.. i sent you photo on facebook..

2
Yamaha / Re: XT250 2valve tuning?
« on: October 20, 2019, 03:57:28 am »
mikuni vm carb and free flowing exhaust and make it light as possible

3
Yamaha / Re: DT2MX
« on: October 20, 2019, 03:55:58 am »
...iain.. it hits the aftermarket pipe that i have fitted .. DT2MX in  PDV frame...i dont even know if the kickstart is correct ,i'd send you a photo but i dont know how..

4
Yamaha / Re: DT2MX
« on: October 17, 2019, 05:18:37 am »
i think i'll just heat and put an s bend in the standard one.... cheers anyway for the replies..

5
Yamaha / Re: DT2MX
« on: October 14, 2019, 10:55:54 pm »
Thanks ... Much appreciated ????

6
Yamaha / Re: DT2MX
« on: October 14, 2019, 05:41:52 pm »
I did , no matches were found ..hence I'm asking here ..

7
Yamaha / DT2MX
« on: October 14, 2019, 04:27:19 am »
I need a shorter kick start on my DT2MX .. anyone any ideas what would fit ?

8
For Sale / Re: DT1 250 after market exhaust
« on: January 06, 2019, 04:10:11 am »
jimson.. would you sent to the uk ? ..regards Davy

9
Honda / Re: Honda xl 350 dellorto phbe 36mm
« on: December 12, 2018, 11:34:18 pm »
Brewster...seizing is never good... motek ignition is a rare thing these days , i use eletrex world electronic ignition ... a vast improvement everywhere..

10
Honda / Re: Honda xl 350 dellorto phbe 36mm
« on: December 11, 2018, 11:47:23 pm »
cheers for all replies... ive got a starting point from a dellorto dealer...ab  262 atomiser,k4 needle , 60 pilot ,130 main, 50 slide... be next year before i finish bike , ive nearly got all the parts gathered, another Honda XL in a husky frame, i built one 2 years ago and it goes well  my son prefers to the C&J framer i have ...

11
Honda / Re: Honda xl 350 dellorto phbe 36mm
« on: December 11, 2018, 05:43:02 am »
excellent jack... i'll check out jetting for a beemer and go from there  8) 8)

12
Honda / Re: Honda xl 350 dellorto phbe 36mm
« on: December 03, 2018, 09:06:02 pm »
i use mikuni vm on my hondas , got the jetting perfect,however i got this dellorto for 20 quid , its like new , ab 270 atomiser , 150 main ,50 pilot , k5 needle , 5 slide ... i'll throw it on and see what happens  8)

13
Honda / Honda xl 350 dellorto phbe 36mm
« on: December 02, 2018, 10:55:25 pm »
Anyone had any success with the above carb on honda xl 350... if so do you have a jetting start point ?

14
Honda / Re: Honda xl jetting 34mm mikuni
« on: August 30, 2018, 04:27:52 am »
34mm mikuni jetting in my vmxl ... 6DH3 needle ,P5-159 needle jet ,35 pilot jet , 220-250 main jet , 2.5 - 3.5 slide and remove air jet , 50/50 av gas and super unleaded mix, electronic ignition , bored ported cam etc etc  ..

15
Honda / Re: Honda xl jetting 34mm mikuni
« on: August 28, 2018, 04:29:18 am »
fit an electrex world electronic ignition and your bike will be transformed ... best cash youll spend

Pages: [1] 2 3 ... 7