1
Suzuki / Re: 1976 RM 370A
« on: October 26, 2025, 05:41:23 pm »
The new style shaft is 20mm diameter is installed on and after RM250-21024 and RM370-17949.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1] 2
2
Suzuki / Re: 82 rm465 kickstarter
« on: June 16, 2020, 01:12:02 pm »
A kick start lever from these models should fit: PE175 80-84, PE250 80-81, PE400 80-81, RM125 81-88, and RM250 82-95.
Try part number 26231-22A10.
Cheers John
Try part number 26231-22A10.
Cheers John
3
For Sale / NOS Suzuki Fork Guards
« on: May 29, 2020, 03:25:57 pm »
NOS Suzuki Fork Guards, left and right. Part #'s 51501-27C40 and 51511-27C40.
Fit RM125 89-91, RM250 89-92 and RMX250 89-96. $50 for the pair.
Can send photo's
Fit RM125 89-91, RM250 89-92 and RMX250 89-96. $50 for the pair.
Can send photo's
4
For Sale / Re: 74-77 YZ125 barrels and heads
« on: May 21, 2020, 02:15:34 pm »
Hi Peter
The number is 1G800.
Regards John
The number is 1G800.
Regards John
5
For Sale / 1982 YZ250J NOS clutch cover
« on: May 17, 2020, 09:20:09 pm »
1982 YZ250J NOS clutch cover and water pump cover. $300
Can send photo's, pick up only, Central Coast NSW.
Can send photo's, pick up only, Central Coast NSW.
6
For Sale / 1985 KX250 Front Forks
« on: May 14, 2020, 06:18:33 pm »
1 x set of 1985 KX250 forks, missing axle clamps but otherwise excellent condition. $400
Pick up only, Central Coast NSw.
Pick up only, Central Coast NSw.
7
For Sale / IT400C barrel
« on: May 14, 2020, 06:13:55 pm »
1 x IT400C 1976 barrel 84.86 mm excellent condition. $300
Pick up only, Central Coast NSW.
Pick up only, Central Coast NSW.
8
For Sale / 74-77 YZ125 barrels and heads
« on: May 14, 2020, 06:09:30 pm »
2 x 74-77 YZ125 barrels and heads, one 56.23 mm the other 56.38 mm. $300 each
Pick up only, Central Coast NSW.
Pick up only, Central Coast NSW.
9
For Sale / Yamaha YZ125J Front ends
« on: May 14, 2020, 06:04:44 pm »
1 x brand new YZ125J front forks and bottom triple clamp with steering stem. $800
1 x used YZ125J front forks and bottom triple clamp with steering stem. $400
Can send photo's. Pick up only, Central Coast NSW
1 x used YZ125J front forks and bottom triple clamp with steering stem. $400
Can send photo's. Pick up only, Central Coast NSW
10
For Sale / 89-04 KX500 right case clutch and mag cover
« on: May 14, 2020, 01:25:11 pm »
89-04 right engine case, #KX500BE 0108** $350
Clutch cover and water pump housing. $300
Magneto cover. $40
All in excellent condition, can send photo's.
Pick up only. Central Coast NSW
Clutch cover and water pump housing. $300
Magneto cover. $40
All in excellent condition, can send photo's.
Pick up only. Central Coast NSW
11
Wanted / Re: suzuki pe175
« on: September 11, 2017, 02:11:28 pm »
Where are you? I have a tank that will fit.
12
Honda / Re: honda xl250 34mm mikuni jetting
« on: March 08, 2017, 07:55:03 pm »
I have the Sudco Mikuni specs for a 32mm Mikuni: Main Jet 4/042 #170, Pilot Jet VM22/210 #25, Needle Jet 159 P5, Throttle Valve VM32/66 3.0, Air Jet BS30/97 2.0, Needle Valve VM34/39 3.3 and Needle 6F4-3.
Hope this helps.
Regards
John
Hope this helps.
Regards
John
14
Suzuki / Re: Mikuni 32mm and 34mm round slide jetting
« on: June 23, 2016, 07:42:25 pm »
Hi Mike, here are my jetting specs for a 74 TM250 with a 34mm round slide Mikuni at 32:1 with Circle F pipe.
M.J.: 210
Needle: 6FJ6-3
N.J.: Q-6
Slide C.A.: 2.0
P.J.: 35
Good luck.
John
M.J.: 210
Needle: 6FJ6-3
N.J.: Q-6
Slide C.A.: 2.0
P.J.: 35
Good luck.
John
15
Wanted / Re: Profab decal
« on: April 07, 2016, 08:30:24 pm »
Hi, I have some black and white Pro-Fab decals that I am looking to get copied. But Dan at Motographics is not interested, and wanted to charge me $150 up front to set up.
Do you have a sticker maker in mind?
Regards
John
Do you have a sticker maker in mind?
Regards
John
Pages: [1] 2