31
Vintage Track / MY new TM250 Project
« on: May 03, 2014, 10:35:09 PM »
I am lucky enough to get this one from Rookie and take over the project where another fellow Robert had stopped. Will be a dirt tracker running on methanol
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
32
Tech Talk / Suzuki cush drive end play TM250
« on: April 30, 2014, 11:08:22 PM »
Gday,
I have assembled the cush drive into the back wheel using new rubbers. there is about 30 thou end play between the cir clip and the sprocket boss, is this normal or should i pack some rubber beneath the cush drives or maybe make a shim washer?
Cheers
I have assembled the cush drive into the back wheel using new rubbers. there is about 30 thou end play between the cir clip and the sprocket boss, is this normal or should i pack some rubber beneath the cush drives or maybe make a shim washer?
Cheers
33
Tech Talk / RM250A or B Swingarm measurement needed please
« on: April 28, 2014, 10:19:01 PM »
Gday Gents,
Can someone please give me the width of the swingarm pivot point where it fits between the frame. or even the width between the frame...
I recently purchased an aluminium T and M swingarm for my TM250 while trying to fit it i found that it was so far different to the TM dimensions that it could not be for a TM. I saw a picture of one for a RM250A and looks the same as mine.
Brett
Can someone please give me the width of the swingarm pivot point where it fits between the frame. or even the width between the frame...
I recently purchased an aluminium T and M swingarm for my TM250 while trying to fit it i found that it was so far different to the TM dimensions that it could not be for a TM. I saw a picture of one for a RM250A and looks the same as mine.
Brett
35
Wanted / Wanted Kick Starter for a DR500 to put on my TM250 project
« on: April 23, 2014, 05:41:29 PM »
Hello,
I am looking for a kick starter to suit a DR500. It is the type which has a very coarse spline and the spline is clamped on the shaft. Not the one that is fastened by the face bolt.
Cheers Brett
I am looking for a kick starter to suit a DR500. It is the type which has a very coarse spline and the spline is clamped on the shaft. Not the one that is fastened by the face bolt.
Cheers Brett
36
Tech Talk / Will this kick starter fit a TM250?
« on: April 22, 2014, 07:47:41 PM »
Thanks for any assistance...
http://www.ebay.com.au/itm/271248802091?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1423.l2649
http://www.ebay.com.au/itm/271248802091?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1423.l2649
37
Wanted / KICK starter for TM250
« on: April 07, 2014, 08:30:32 PM »
I require a good kick starter for my project... it has a very coarse spline..
Please PM me if you have one
Cheers Brett
Please PM me if you have one
Cheers Brett
38
Tech Talk / Can someone tell me the dimensions of the KV100 / G4TR rear axle adjusted
« on: March 29, 2014, 09:14:39 PM »
I am wanting to find a suitable rear axle adjuster to use on my newly acquired alloy swingarm for my TM suziki. I have attached a part. I need:
Axle diameter and the thread size M6 or M8...
ANy help appreciated
http://www.ebay.com.au/itm/KAWASAKI-KV100-G4TR-70-76-LH-CHAIN-ADJUSTER-NOS-OEM-/370377087347?pt=Motorcycles_Parts_Accessories&hash=item563c31d973
Cheers Brett
Axle diameter and the thread size M6 or M8...
ANy help appreciated
http://www.ebay.com.au/itm/KAWASAKI-KV100-G4TR-70-76-LH-CHAIN-ADJUSTER-NOS-OEM-/370377087347?pt=Motorcycles_Parts_Accessories&hash=item563c31d973
Cheers Brett
39
For Sale / YZ250 D or E or 400 Opaque side covers New $55 incl postage aust VMX unlimited
« on: March 26, 2014, 09:29:09 PM »
From Les originally, surplus to my project
Brett
0417 42971eigth
Brett
0417 42971eigth
40
Bike Talk / T and M engineering Aluminium Swingarm on TM250 Is it possible to run in pre 75
« on: March 17, 2014, 09:19:05 PM »
Just wondering if i should go to the trouble on my new TM project....
Brett
Brett
41
General Discussion / No national SX for NSW again in 2014 WTF
« on: March 16, 2014, 12:51:17 PM »
NSW missed out last year, i have not missed an event for 15 years till that point, my son loves it. I just cannot believe there is no plan for sydney... Will go to Appin instead to see MX
Brett
Brett
44
General Discussion / someone fresh my memory, there was a really nice RM125S in US pictured on here
« on: March 03, 2014, 08:15:44 PM »
I really want to see the photo again which was pasted on the forum to get colour ideas for my new project TM250....
Cheers Brett
Cheers Brett
45
Competition / Nepean STgeorge Dirt track cancelled for Sunday 2nd March DUE TO RAIN
« on: March 01, 2014, 02:41:00 PM »
Nepean STgeorge Dirt track cancelled for Sunday 2nd March