OzVMX Forum

Marque Remarks => Suzuki => Topic started by: southnztim on October 03, 2009, 06:08:25 pm

Title: Pe 250 T Clutch cover
Post by: southnztim on October 03, 2009, 06:08:25 pm

Does anyone know if a PE 250T has the same clutch cover as a PE 400. Thanks, Tim

Title: Re: Pe 250 T Clutch cover
Post by: oldfart on October 03, 2009, 07:09:43 pm

NO  not the same   different at locating pins .......but very close

Title: Re: Pe 250 T Clutch cover
Post by: suzuki27 on October 03, 2009, 07:21:50 pm

Not dead sure but I reckon the RM 250T is the same and the PE 175 as well.

Title: Re: Pe 250 T Clutch cover
Post by: DR on October 03, 2009, 08:35:28 pm

this is in the Parts For Sale section..a maybe perhaps..

 2009-08-31 suzuki PE 250 N or T parts camden 46571213 or 0410713454 $ 1.00 No Picture
Have a bike which has been dismantled most parts are there. email [email protected]

Title: Re: Pe 250 T Clutch cover
Post by: lukeb1961 on October 03, 2009, 08:56:06 pm

Quote from: southnztim on October 03, 2009, 06:08:25 pm

Does anyone know if a PE 250T has the same clutch cover as a PE 400. Thanks, Tim

NO. close, but not quite matched. The locating dowel thingies are different.
Do you need for a 250 or for a 400?

Title: Re: Pe 250 T Clutch cover
Post by: LWC82PE on October 03, 2009, 10:39:15 pm

Part # = 11341-40300
Part Description = COVER,CLUTCH
Model Count = 7
PE250T 1980
PE250X 1981
RM250-N 1979
RM250-T 1980
RM250-X 1981
RS250T 1980
RS250X 1981

Title: Re: Pe 250 T Clutch cover
Post by: southnztim on October 04, 2009, 06:17:07 am

Thanks for the info guys. Unfortunately put a hole through my 250's one. Was hoping,just maybe that the 400's might fit. At least, that list widens the field a bit. Will try that address and keep my fingers crossed. Cheers

Title: Re: Pe 250 T Clutch cover
Post by: oldfart on October 04, 2009, 07:49:15 am

Let me see , hole caused by kick lever.   

Title: Re: Pe 250 T Clutch cover
Post by: DR on October 04, 2009, 12:19:59 pm

I've had a 2 part epoxy ribbon type repair in my RM400 case for about ummm..25 years I guess. The poor man alternative ;D Most probably used Selley's cause..it works! ;)

Title: Re: Pe 250 T Clutch cover
Post by: lukeb1961 on October 04, 2009, 12:28:10 pm

JB Weld is your friend  ;D

Title: Re: Pe 250 T Clutch cover
Post by: southnztim on October 04, 2009, 01:37:34 pm

Second cover with a hole in it! Coming off on the left side and gear selector shaft punching the stop through the cover. Grrrr

Title: Re: Pe 250 T Clutch cover
Post by: oldfart on October 04, 2009, 08:11:40 pm

make sure you install a nylon    bush ( roller on selector shaft ) between seal & gear lever
Some models had a thin ( 3mm ) stopper shaft that had a nylon bush .....   see  Suzuki parts book
http://www.alpha-sports.com/suzuki_parts.htm

go to 1980-  Rm 250  - gear shifting        parts  23 & 27