OzVMX Forum

Marque Remarks => Suzuki => Topic started by: oldfart on May 22, 2009, 07:28:47 pm

Title: Rm 250 T axle LHS spacer Rear
Post by: oldfart on May 22, 2009, 07:28:47 pm
Shit happens ??? picked up my items from platter this sarvo and the above item is missing  ???

Can someone supply me with the dimensions So I can  get one turned up .     LHS axle spacer Rear

I've knocked the centre out of an old bearing    6202 which is close ( 10mm long ) AS AN INTERIM
Title: Re: Rm 250 T axle LHS spacer Rear
Post by: oldfart on May 25, 2009, 07:07:00 pm
Ok I'll try a different approach, Does anyone want to sell me a Rear axle assembly For a Rm 250 T .
Title: Re: Rm 250 T axle LHS spacer Rear
Post by: pmc57 on May 25, 2009, 09:07:32 pm
So length is about 10mm, what's the OD, ID and any other features? I can have a look in my box of goodies to see what I've got.
Title: Re: Rm 250 T axle LHS spacer Rear
Post by: Tornado on May 25, 2009, 09:15:48 pm
will measure mine tomorrow if you can wait
Title: Re: Rm 250 T axle LHS spacer Rear
Post by: oldfart on May 25, 2009, 09:28:42 pm
part   # 19
Title: Re: Rm 250 T axle LHS spacer Rear
Post by: Tornado on May 25, 2009, 09:45:19 pm
7 pm tomorrow night  and ps thanks for the parts fiche-makes things a whole lot less confusing
Title: Re: Rm 250 T axle LHS spacer Rear
Post by: Tornado on May 26, 2009, 08:38:26 pm
Well picked up my verniers and they are digital but with a flat battery they are only good for measuring oranges for an orange gun. there is no fine markings on the shaft to be accurate. will get another battery tomorrow and measure tomorrow night.

sorry
Title: Re: Rm 250 T axle LHS spacer Rear
Post by: pmc57 on May 26, 2009, 08:44:04 pm
Nothing in my box of goodies, sorry
Title: Re: Rm 250 T axle LHS spacer Rear
Post by: oldfart on May 26, 2009, 08:52:53 pm
Thanks for looking      Pete
Title: Re: Rm 250 T axle LHS spacer Rear
Post by: suzuki27 on May 28, 2009, 05:48:19 pm
How did you go ?. I can measure mine on the w/end and report back if still needed.The LHS has a small raised section on the side that points towards the wheel bearing-this slightly wider section does not extend all the way to the perimeter of the spacer...from memory.
Title: Re: Rm 250 T axle LHS spacer Rear
Post by: oldfart on May 28, 2009, 05:55:59 pm
THATS THE ONE ....memory tells me it abuts bearing small face, then has a step up with clearance around hub.
If you could measure that would be much appreciated
Title: Re: Rm 250 T axle LHS spacer Rear
Post by: suzuki27 on May 28, 2009, 06:54:36 pm
Yep. I will get it done this w/end.
Title: Re: Rm 250 T axle LHS spacer Rear
Post by: Tornado on May 28, 2009, 07:00:52 pm
so the pics I emailed helped? or made it worse?
Title: Re: Rm 250 T axle LHS spacer Rear
Post by: oldfart on May 28, 2009, 09:03:23 pm
Tex, pics Helped thanks :) . Measurements is what I needed
Title: Re: Rm 250 T axle LHS spacer Rear
Post by: DR on May 28, 2009, 09:30:42 pm
excuses excuses...ya fussy ol' bastard oldfart! ::) so the new zinc plating didn't match the offcut of galv waterpipe spacer you were using and now you want to make a replacement from some exotic zinc plated substance ::) blaming the platers..as if they'd lose anything like that!! ;D
Title: Re: Rm 250 T axle LHS spacer Rear
Post by: oldfart on May 29, 2009, 04:02:31 pm
wish it was that easy Chris,  A lathe is my next purchase
Guest what ....It's piissing with rain again as I punch away at key board  ::)
Remember this pic from last year
Title: Re: Rm 250 T axle LHS spacer Rear
Post by: DR on May 29, 2009, 04:07:40 pm
 :D sure I remember young fella, I was praising the heavens for the little shower and a wee puddle it left....right at the bloody entrance!! ::) no rain here at this momnet but I guessed from the look of the sky someone would be getting it ;)
Title: Re: Rm 250 T axle LHS spacer Rear
Post by: suzuki27 on May 30, 2009, 05:45:09 pm
The measurements for the LHS spacer are: the narrow part towards the outside of the spacer is 9.7mm. I got readings of 9.6 to 9.8 mm, so 9.7mm is good. Now, the raised section that faces the wheel bearing is 10.7mm. So that wider section is 1mm wider. ID is 15mm and OD is 34mm.  The RHS spacer is 7mm wide with same ID & OD. Cheers.
Title: Re: Rm 250 T axle LHS spacer Rear
Post by: oldfart on May 30, 2009, 07:28:46 pm
THANK VERY MUCH  :)   I'll get them turned up on monday
Title: Re: Rm 250 T axle LHS spacer Rear
Post by: Lozza on May 30, 2009, 10:30:20 pm
Is that right ??? Are you walking on that water Doc or is it some optical illusion? I wondered how wet it was up there.

Stew have a look at a HQ500M (http://wic020u.server-secure.com/vs4487_secure/product.asp?dept_id=136&product_id=HQ500IM&viewsoh=0&crord=1&mscssid=1&cid=11) from Minitech in Brisbane, has long and cross power feeds and a great big table,mine was $2600 delivered.
Title: Re: Rm 250 T axle LHS spacer Rear
Post by: DR on May 31, 2009, 06:35:03 am
optical illusion Loz, I was only at the edge as the water. The entrance just past the armco was not navigational by car, 4wd or foot until later that day ;)