OzVMX Forum

Marque Remarks => Spaniards (Bultaco, Ossa, Montesa etc) => Topic started by: evo550 on November 22, 2008, 04:50:59 pm

Title: Phantom ignitions
Post by: evo550 on November 22, 2008, 04:50:59 pm
Anyone know which one fits a gp2?
http://cgi.ebay.com/ebaymotors/OSSA-PHANTOM-IGNITION-AHRMA_W0QQcmdZViewItemQQ_trkparmsZ72Q3a1205Q7c66Q3a2Q7c65Q3a12Q7c39Q3a1Q7c240Q3a1318QQ_trksidZp3286Q2ec0Q2em14QQhashZitem360109345265QQitemZ360109345265QQptZMotorcyclesQ5fPartsQ5fAccessories
http://cgi.ebay.com/ebaymotors/OSSA-PHANTOM-LOWER-MOTOPLAT-IGNITION-AHRMA_W0QQcmdZViewItemQQ_trkparmsZ72Q3a1205Q7c66Q3a2Q7c65Q3a12Q7c39Q3a1Q7c240Q3a1318QQ_trksidZp3286Q2ec0Q2em14QQhashZitem120337478390QQitemZ120337478390QQptZMotorcyclesQ5fPartsQ5fAccessories
Title: Re: Phantom ignitions
Post by: JC on November 24, 2008, 09:39:07 am
Br,

If its any help, 74 Phantom Ign part # 123025M1
75 GP # 123025BM1
76 GP2 # 123025BM1
Title: Re: Phantom ignitions
Post by: evo550 on November 24, 2008, 09:56:27 am
Jc,
The seller doesn't know what phantom's they came in a mass spare parts lot.
They should fit all phantoms as the crank and stator mounts should be the same, I just don't know if the gp2 and 3's had a smaller flywheel to fit under the smaller case.
Title: Re: Phantom ignitions
Post by: OSSA PHANTOM on November 25, 2008, 08:14:30 pm
 Th OSSA phantom ignition will fit under the newer style side cover as will a PVL ignition. The desert phanton ignition cannot be used on a MX phantom unless you swap the crankshaft halves, the desert phantom ignition will not fit under the newer style sidecover.
 I know that it is a bit pricey but a PVL or MZB ignition is probably the way to go. the swapping crank halves is costly and I wouldn't have done it had the MZB ignition with the lighting been available.
 When my desert phantom engine motoplat dies I'll be replacing it with an MZB, My GP3 engine uses
a PVL and my GP2 engine has a rebuilt Bradford motoplat.
Title: Re: Phantom ignitions
Post by: evo550 on November 25, 2008, 09:16:25 pm
Someone is claiming that neither of them suit a phantom (I think it might be Keith Lynas)
Anyone deny/confirm....hate to get something that's not going to fit, nearly as much as missing something that will fit.
Title: Re: Phantom ignitions
Post by: OSSA PHANTOM on November 25, 2008, 10:36:44 pm
 The second unit looks to be a phantom MX unit which will fit under the new cover, attached is photo of a new stye cover I cast a few years ago.
Title: Re: Phantom ignitions
Post by: evo550 on November 26, 2008, 08:16:38 am
Did you sell one of these on ebay a few years ago?
I bought a homemade one...it was very well done.
Title: Re: Phantom ignitions
Post by: OSSA PHANTOM on November 26, 2008, 07:05:54 pm
 Evo,
  Yes it was I. I had I had more funds I would have die cast them instead of sand casting. I keep a couple for my bikes and sold the rest to Alex Snoop.