OzVMX Forum

Marketplace => Wanted => Topic started by: Tony.Brown on December 29, 2015, 10:46:25 am

Title: PE250T or later bottom end or crank to suit rebuild
Post by: Tony.Brown on December 29, 2015, 10:46:25 am

Hi all, a good friend is looking for either a rebuildable crank but would prefer a whole bottom end to suit his 1980 PE250T.
Anything out there?
Either PM me here or phone or sms me on 0421985762
Regards, Tony.

Title: Re: PE250T or later bottom end or crank to suit rebuild
Post by: pecrazy on December 29, 2015, 10:52:39 am

I have the worlds worst looking PE250 crank here if he cannot find a better one on earth. What is wrong with his?

Title: Re: PE250T or later bottom end or crank to suit rebuild
Post by: Tony.Brown on December 29, 2015, 10:54:24 am

The threaded end is all kinds of f@#*ed up, what's up with yours?

Title: Re: PE250T or later bottom end or crank to suit rebuild
Post by: pecrazy on December 29, 2015, 11:01:27 am

Bearing fell apart, then got a little water damaged but the ends are great.

Title: Re: PE250T or later bottom end or crank to suit rebuild
Post by: Tony.Brown on December 29, 2015, 11:04:05 am

Sounds good, he has a rod kit ordered for his, then discovered the damage, what model it yours from, or doesn't it matter?

Title: Re: PE250T or later bottom end or crank to suit rebuild
Post by: pecrazy on December 29, 2015, 11:05:07 am

1980 PE250 I think the early ones were different.

Title: Re: PE250T or later bottom end or crank to suit rebuild
Post by: Tony.Brown on December 29, 2015, 11:09:39 am

I have sent you a pm.

Title: Re: PE250T or later bottom end or crank to suit rebuild
Post by: LWC82PE on December 29, 2015, 11:11:44 am

80-82 PE250 are the same crank, also 80-81 RS250 uses same crank. Try looking on USA ebay for RS250 crank instead. I need a couple myself and its certainly not a PE part that i would go into a panic trying to find. There are many more harder parts to find than this.

Title: Re: PE250T or later bottom end or crank to suit rebuild
Post by: Tony.Brown on December 29, 2015, 11:20:35 am

No panic Leith, I figure there will be plenty of these sitting in sheds of forum members, just rather trust the forum members than going straight to Ebay.
Tony.

Title: Re: PE250T or later bottom end or crank to suit rebuild
Post by: BA #63 on December 29, 2015, 05:59:50 pm

complete bike on gumtree wa  for a grand then you got lots of spares

Title: Re: PE250T or later bottom end or crank to suit rebuild
Post by: Oldfart on December 29, 2015, 06:31:55 pm

How many do you want ...

Title: Re: PE250T or later bottom end or crank to suit rebuild
Post by: Tony.Brown on December 29, 2015, 06:48:48 pm

Only one required.
Tony.

Title: Re: PE250T or later bottom end or crank to suit rebuild
Post by: Oldfart on December 29, 2015, 08:24:07 pm

Ok can do ....will ring you tommorow early morning ish

Title: Re: PE250T or later bottom end or crank to suit rebuild
Post by: Tony.Brown on December 29, 2015, 09:55:45 pm

Look forward to it oldfart!

Title: Re: PE250T or later bottom end or crank to suit rebuild
Post by: Glen08 on January 11, 2016, 08:59:45 am

I'll have a look today ..but I think I have one if your still looking.

Title: Re: PE250T or later bottom end or crank to suit rebuild
Post by: Tony.Brown on January 11, 2016, 09:08:23 am

I'll check with him to see if he still needs one, thankd Glen08.

Title: Re: PE250T or later bottom end or crank to suit rebuild
Post by: Glen08 on January 11, 2016, 09:35:43 am

Ok.
Glen.

Title: Re: PE250T or later bottom end or crank to suit rebuild
Post by: Tony.Brown on January 12, 2016, 09:24:22 pm

Hi Glen08, I managed to contact him and he has found one already, thank you for your offer and sorry I couldn't let you know sooner.
Tony.

Title: Re: PE250T or later bottom end or crank to suit rebuild
Post by: Glen08 on January 13, 2016, 08:02:27 am

That's fine mate..