OzVMX Forum

Marketplace => Wanted => Topic started by: suzuki447 on March 04, 2015, 09:57:35 pm

Title: 81pe175 complience plate wanted or one i can use.
Post by: suzuki447 on March 04, 2015, 09:57:35 pm: after a compliance plate to get my pe rego,d .
Title: Re: 81pe175 complience plate wanted or one i can use.
Post by: Goose 29 on March 18, 2015, 09:37:44 am: I have a couple but are 1979 and 1980 I think,
I am in Melbourne. Andrew.
Title: Re: 81pe175 complience plate wanted or one i can use.
Post by: suzuki447 on March 18, 2015, 09:13:31 pm: interested in 80plate. my ph 0410383202 tx me how much .thanks don.
Title: Re: 81pe175 complience plate wanted or one i can use.
Post by: LWC82PE on March 18, 2015, 09:39:34 pm: Keep in mind that the compliance plate number is supposed to match the number stamped on the frame too on Suzukis.
Title: Re: 81pe175 complience plate wanted or one i can use.
Post by: Goose 29 on March 19, 2015, 10:14:13 am: My plates are next to stamped frame and do not match on both bikes.
Title: Re: 81pe175 complience plate wanted or one i can use.
Post by: 80-85 husky on March 19, 2015, 10:45:14 am: what reg and what state are you in?
Title: Re: 81pe175 complience plate wanted or one i can use.
Post by: kdx Geoff on March 19, 2015, 11:46:17 am: Quote from: LWC82PE on March 18, 2015, 09:39:34 pm
Keep in mind that the compliance plate number is supposed to match the number stamped on the frame too on Suzukis.

Quote from: Goose 29 on March 19, 2015, 10:14:13 am
My plates are next to stamped frame and do not match on both bikes.

So does that mean that the frame number on the frame isn't identical to the frame number on the compliance plate ?
Title: Re: 81pe175 complience plate wanted or one i can use.
Post by: LWC82PE on March 19, 2015, 05:34:26 pm: I got 6 suzukis and all the compliance plates have the number matching the frame number

Quote
My plates are next to stamped frame and do not match on both bikes

I would say either someone broke a frame and replaced it or 'lost' the comp plate and stuck another one on it.
Title: Re: 81pe175 complience plate wanted or one i can use.
Post by: DR500 on March 19, 2015, 11:14:41 pm: when you get a rwc inspection they will check that they match up
Title: Re: 81pe175 complience plate wanted or one i can use.
Post by: b490 on March 20, 2015, 09:13:46 pm: Compliance plate requirement for registered motorcycles sold in Australia was introduced for motorcycles produced on or after
the 1st October 1976 .

Frame # / ID # stated on compliance plate must match frame / ID number of the bike.

Regards ,
Steve
Title: Re: 81pe175 complience plate wanted or one i can use.
Post by: 80-85 husky on March 21, 2015, 08:56:40 am: if your in Victoria and chasing club reg or recreational reg you do not need a compliance plate
Title: Re: 81pe175 complience plate wanted or one i can use.
Post by: frostype400 on March 21, 2015, 10:20:34 am: The engine number won't match on a pe but the frame neck number and Comp plate always do you won't need the plate for rego installing one not from the bike will come across as dodgy illegal to do.

They don't look at the comp plate if you are worried take some photos of where it normally is they will see the rivets every time I have taken Vic roads a car or bike they only wanted to see the vin and engine number.
Title: Re: 81pe175 complience plate wanted or one i can use.
Post by: oldyzman on March 21, 2015, 01:46:07 pm: so can i get a TM250 1974 registered in NSW, if it has the correct lights etc?
Title: Re: 81pe175 complience plate wanted or one i can use.
Post by: bigk on March 21, 2015, 04:08:32 pm: Every time I have taken bikes to Vic Roads, new or old, to be registered or re-registered, they ALWAYS check the compliance plate for the date. They rarely check that the frame number matches though. I have done this hundreds of times.
K
Title: Re: 81pe175 complience plate wanted or one i can use.
Post by: GMC on March 21, 2015, 04:18:16 pm: You won't need a compliance plate prior to 76 as they didn't exist earlier.
However it will have to meet all of the rego requirements

Getting a bike registered without one should be easier if you have proof it had previously been registered.
Title: Re: 81pe175 complience plate wanted or one i can use.
Post by: huskibul on March 21, 2015, 05:35:42 pm: If your talking about NSW - good luck with that ! we're talking the biggest nanny state on the planet and every rms officer/engineer you talk will have a different interpretation depending on how they feel on the day ::)
Title: Re: 81pe175 complience plate wanted or one i can use.
Post by: suzuki447 on March 23, 2015, 10:39:52 pm: thanks for feedback I,m in nsw .they don't make it easy here.
Title: Re: 81pe175 complience plate wanted or one i can use.
Post by: suzuki447 on March 30, 2015, 10:52:45 pm: im in nsw guys bike is ready for rego with everything working lights blinkers everything but compl plate missing.u would think that approval no for an 81 pe175 would be same no on every 81pe175 .just engine and frame no,s different for each one. can someone at least tell me the approval no..thanks don.
Title: Re: 81pe175 complience plate wanted or one i can use.
Post by: 80-85 husky on March 31, 2015, 09:44:00 pm: I saw somewhere that the new vic historic reg rules require a compliance plate. :'( I will have to forward pay the rego!!!