OzVMX Forum

Marketplace => Wanted => Topic started by: twinrock on June 28, 2008, 10:49:01 pm

Title: pre 1980 it175 barrel
Post by: twinrock on June 28, 2008, 10:49:01 pm

as it states any condition concidered..im in newcastle

Title: Re: pre 1980 it175 barrel
Post by: cyclegod on June 28, 2008, 11:04:43 pm

Expensive, but then it is NEW....

http://cgi.ebay.com/ebaymotors/YAMAHA-NOS-CYLINDER-BARREL-JUG-IT175-IT-175_W0QQcmdZViewItemQQcategoryZ35595QQihZ012QQitemZ220228398535QQrdZ1QQsspagenameZWDVW

but this is for a '78

http://cgi.ebay.com/ebaymotors/78-Yamaha-IT175-IT-175-Stock-Bore-Cylinder-Head_W0QQcmdZViewItemQQcategoryZ35595QQihZ002QQitemZ120272410145QQrdZ1QQsspagenameZWDVW

Title: Re: pre 1980 it175 barrel
Post by: Freakshow on June 30, 2008, 02:10:38 pm

YEs i have found a guy that has a few IT he is breaking up, all years, all parts. 

Send me a list and the prices youll go too, ill put the hard word on him and see if i can get em for any thing less than what you want to pay and see if i can get them out of him, happy to post to you for whatever it cost to wherever you are also

there was at least 3 barrels i saw, tanks, shocks, electrics, plastics.  that went for a 84 CR 250 and i also saw some pre 85 Suzi's in there too.

Title: Re: pre 1980 it175 barrel
Post by: ELC hunter on June 30, 2008, 06:15:31 pm

what prefix barrel is it you need,i have one but not sure if it or dt elc.

Title: Re: pre 1980 it175 barrel
Post by: 090 on June 30, 2008, 10:03:55 pm

I also have some IT stuff. If you can tell me prefix and/or what to look for, i might have something.

Title: Re: pre 1980 it175 barrel
Post by: Nathan S on June 30, 2008, 10:32:04 pm

1W2 is what he wants.
3R6 or 5X8 are no good.
Any monoshock DT175 barrel will do the job too - they're the ones with 6 studs coming out of the barrel to hold the head on.
The late (1985+) DT175 barrels are the best of the lot - they can be identified by the bridged intake port, and the case-to-barrel nuts that can be removed with a ring spanner (the earlier ones need a socket - this will be obvious when you look at the barrel).

I'm also looking for a 1W2 IT175, or 2A7 DT175 barrel, but Twinny has first dibbs.

Edit: I'm a fat-fingered idiot.... 2A7 = DT175, 2A6 = DT125... Thanks for the gentle prod, Noel. :)

Title: Re: pre 1980 it175 barrel
Post by: Freakshow on June 30, 2008, 10:40:54 pm

Nat i seen about 3 in salvage just this morning. infact i was trying to steal the foot peg off one butit was raining so i told him id come back.

Title: Re: pre 1980 it175 barrel
Post by: Noel on June 30, 2008, 10:52:42 pm

nathan,
PM sent re 2a7 barrel

Title: Re: pre 1980 it175 barrel
Post by: ELC hunter on July 01, 2008, 07:50:30 pm

just looked at prefix 2a7 61.5 mm fresh rebore. elc