OzVMX Forum

Marketplace => For Sale => Topic started by: jimg1au on November 25, 2013, 07:14:58 am

Title: one more project bike pre75 antig honda xl250 slider
Post by: jimg1au on November 25, 2013, 07:14:58 am

have most parts for a antig 250 xl honda  spare parts engine
needs total reco was my frame sold to firko but have it back though i might need parts for my antig bultaco but all good
has gen antig hubs with drum brakes front and back
frame small bend near stearing head easy fix forks ok
have fiberglass and tank
1300.00 ono
parts are in sydney

Title: Re: one more project bike pre75 antig honda xl250 slider
Post by: hagon_84 on November 25, 2013, 09:51:45 pm

Hey jim you got any pics of the slider has it got wheels and engine plates? What does it need to finish it off other than rebuild on engine if its easier can u send us some pics to [email protected] cheers Al.

Title: Re: one more project bike pre75 antig honda xl250 slider
Post by: jimg1au on November 25, 2013, 10:21:04 pm

al
have a pic at home will send you one
it needs total resto
complete rear conical rear wheel 19" rim lost surface rust braked
complet frame swing arm chromed slight bend in top rail above tank
complete forks including conical front wheel lots of surface rust braked
tank
seat
rear guard
frame has been shortened in the front downtube to allow c/port yamaha mx/yz250 motor
you will need to make engine plates and footpegs brake leaver pipe ect
orignal girling rear shocks
 xl250  spares motor as well
jim

Title: Re: one more project bike pre75 antig honda xl250 slider
Post by: jimg1au on January 02, 2014, 02:35:34 pm

(http://i414.photobucket.com/albums/pp221/jimg1au/489_zps8be39d5f.jpg) (http://s414.photobucket.com/user/jimg1au/media/489_zps8be39d5f.jpg.html)

(http://i414.photobucket.com/albums/pp221/jimg1au/488_zpsba4da8f5.jpg) (http://s414.photobucket.com/user/jimg1au/media/488_zpsba4da8f5.jpg.html)


(http://i414.photobucket.com/albums/pp221/jimg1au/487_zpsc0e30d67.jpg) (http://s414.photobucket.com/user/jimg1au/media/487_zpsc0e30d67.jpg.html)

(http://i414.photobucket.com/albums/pp221/jimg1au/486_zpsf3bd1fba.jpg) (http://s414.photobucket.com/user/jimg1au/media/486_zpsf3bd1fba.jpg.html)

(http://i414.photobucket.com/albums/pp221/jimg1au/485_zps7e4823dc.jpg) (http://s414.photobucket.com/user/jimg1au/media/485_zps7e4823dc.jpg.html)

(http://i414.photobucket.com/albums/pp221/jimg1au/484_zps6439bfb0.jpg) (http://s414.photobucket.com/user/jimg1au/media/484_zps6439bfb0.jpg.html)

(http://i414.photobucket.com/albums/pp221/jimg1au/483_zpsd20e0310.jpg) (http://s414.photobucket.com/user/jimg1au/media/483_zpsd20e0310.jpg.html)

(http://i414.photobucket.com/albums/pp221/jimg1au/482_zps2b2ec25e.jpg) (http://s414.photobucket.com/user/jimg1au/media/482_zps2b2ec25e.jpg.html)

Title: Re: one more project bike pre75 antig honda xl250 slider
Post by: jimg1au on January 02, 2014, 02:37:56 pm

any 2 stroke motor will go in this frame centre or side port as you just need to make engine plates
jim

Title: Re: one more project bike pre75 antig honda xl250 slider
Post by: firko on January 02, 2014, 03:28:06 pm

Is that my old Antig Jim? The bend in the top rail shows up doesn't it? ::). It's an easy fix for a home handyman with an oxy set. Antigs are getting a bit rare and this one's got the unobtainium Antig hubs and backing plates.

Title: Re: one more project bike pre75 antig honda xl250 slider
Post by: oldyzman on January 02, 2014, 07:41:01 pm

Looks like good value Jim, Even to send it to Laurie for straighteneng - would not cost too much. What year would it be mate?
Brett

Title: Re: one more project bike pre75 antig honda xl250 slider
Post by: jimg1au on January 08, 2014, 06:46:24 pm

sold