OzVMX Forum
Marketplace => Wanted => Topic started by: firko on August 22, 2013, 10:35:59 pm
-
I've asked before and didn't get a result but I'll try again. Has anyone got a reasonable RM250/370 tank they're prepared to sell. I don't mind small dents or leaks....dents can be bogged and leaks welded. PM me...............thanks in advance, Mark.
-
These two have only just finished. No bids.
http://www.ebay.com.au/itm/300949108252?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1438.l2649 (http://www.ebay.com.au/itm/300949108252?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1438.l2649)
http://www.ebay.com.au/itm/300949110161?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1438.l2649 (http://www.ebay.com.au/itm/300949110161?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1438.l2649)
with only $55 / $60 postage quoted on each, I am gob smacked that no one bid on them, as cheap as any I have ever seen, thats for sure.
-
I was going to bid on it Mick but bloody forgot until it was too late.....I might pop him an email.
-
These two have only just finished. No bids.
http://www.ebay.com.au/itm/300949108252?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1438.l2649 (http://www.ebay.com.au/itm/300949108252?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1438.l2649)
http://www.ebay.com.au/itm/300949110161?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1438.l2649 (http://www.ebay.com.au/itm/300949110161?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1438.l2649)
with only $55 / $60 postage quoted on each, I am gob smacked that no one bid on them, as cheap as any I have ever seen, thats for sure.
yes i was gunna have a go but was whating on TMBill ended up getting the one from Bill
-
That's the guy who I got my CZ tank off, was great to deal with & when he found out cost of postage asked me if I still wanted it.
He'll most likely relist it soon so emailing him may pay dividends
-
Can someone give me the dimensions of an RM125 tank the same as the one pictured? Most important are the length and width of the tunnel. I'm thinking of buying this tank but if it doesn't fit it's no good to me.
(http://i1112.photobucket.com/albums/k495/firko2/RM125tank_zpsb835c1a7.jpg) (http://s1112.photobucket.com/user/firko2/media/RM125tank_zpsb835c1a7.jpg.html)
-
Firko 440mm overall and 60 tunnel :)
-
Thanks mate.
-
Can someone give me the dimensions of an RM125 tank the same as the one pictured? Most important are the length and width of the tunnel. I'm thinking of buying this tank but if it doesn't fit it's no good to me.
(http://i1112.photobucket.com/albums/k495/firko2/RM125tank_zpsb835c1a7.jpg) (http://s1112.photobucket.com/user/firko2/media/RM125tank_zpsb835c1a7.jpg.html)
The RM125B tank will on the 250/370B no worries One of the Guns like to use 125 tanks as his std set up, even knew a guy who put a 370 tank on his 125 to make it look trick ;D ;D ???
-
The RM125B tank will on the 250/370B no worries One of the Guns like to use 125 tanks as his std set up, even knew a guy who put a 370 tank on his 125 to make it look trick
I want to paint it silver, put RT2MX Yamaha graphics on it and fit it on a Hindall. Dare to be different I say ;D.
-
The RM125B tank will on the 250/370B no worries One of the Guns like to use 125 tanks as his std set up, even knew a guy who put a 370 tank on his 125 to make it look trick
I want to paint it silver, put RT2MX Yamaha graphics on it and fit it on a Hindall. Dare to be different I say ;D.
Sounds Great , recon it will look the dux nuts ;) always ask for the cap and tap ,never asume! I now have to go back with cap in hand :'(