OzVMX Forum

Clubroom => Tech Talk => Topic started by: rohan on March 02, 2011, 11:13:33 pm

Title: PE400 Flywheel Puller
Post by: rohan on March 02, 2011, 11:13:33 pm

I need to grab a new flywheel puller for the PE. Can anyone point me toward the right one to grab (on ebay or other), ideally something generic that I can use on more than just one engine if possible.

Cheers

Title: Re: PE400 Flywheel Puller
Post by: rohan on March 02, 2011, 11:29:13 pm

Would something like this get me out of trouble?

http://cgi.ebay.com/ebaymotors/Universal-Motorcycle-Flywheel-Puller-ATV-Honda-Suzuki-_W0QQcmdZViewItemQQhashZitem2a0e533af9QQitemZ180628962041QQptZMotorcyclesQ5fPartsQ5fAccessories (http://cgi.ebay.com/ebaymotors/Universal-Motorcycle-Flywheel-Puller-ATV-Honda-Suzuki-_W0QQcmdZViewItemQQhashZitem2a0e533af9QQitemZ180628962041QQptZMotorcyclesQ5fPartsQ5fAccessories)

Title: Re: PE400 Flywheel Puller
Post by: 500Fool on March 03, 2011, 08:32:28 am

I forget what a Suzuki one is like but a Honda/Yam one is a little colar that screws (Left hand thread) into the flywheel, you then screw a shaft (Right hand tread) into the centre till it grounds then just give that shaft a tap, springs orf no problems.

Title: Re: PE400 Flywheel Puller
Post by: AdamN on March 03, 2011, 11:03:17 am

That one should do the job. MCS do a Suzuki flywheel puller, get your local bike shop to look in their MCS catologue, or check it out online.

Adam

Title: Re: PE400 Flywheel Puller
Post by: cyclegod on March 03, 2011, 11:13:38 am

http://cgi.ebay.com/ebaymotors/Suzuki-RM-PE-80-125-250-370-400-Flywheel-Rotor-Puller-_W0QQcmdZViewItemQQhashZitem5adec3bdc4QQitemZ390284426692QQptZMotorcyclesQ5fPartsQ5fAccessories

Title: Re: PE400 Flywheel Puller
Post by: LWC82PE on March 03, 2011, 12:54:38 pm

www.mcsonline.com.au The MCS ones are Dennis Stubblefield brand made in USA and im pretty sure the below websites carry the same ones.

also

www.repairmanual.com

www.denniskirk.com

http://www.mcas.com.au/pw/

Parts Unlimited do a Universl multi fit one. MSC has this aswell i think but i know www.denniskirk.com has it too.

Title: Re: PE400 Flywheel Puller
Post by: rohan on March 03, 2011, 03:53:20 pm

Thanks

Title: Re: PE400 Flywheel Puller
Post by: lukeb1961 on March 05, 2011, 09:06:45 am

you will find the RM one does not fit.

Title: Re: PE400 Flywheel Puller
Post by: LWC82PE on March 05, 2011, 12:36:26 pm

For mine i actually didnt buy the PE specific one and bought a Yam WR400 or TT600 puller. I cant remember which one it was but im leaning towards WR400. I dont know why i bought it either but i think it may of been that i could use it on the TS flywheels too instead of the PE specific one or maybe the PE one was out of stock or something i just cant remember. Anyway all i had to do was  drill the 3 6mm bolt holes out to about 7mm i think so the center distances lined up with the 3 threaded holes in the PE flywheel. Its a pretty compact tool. With a few lightening holes in the plate, you could take the tool with you one a trail ride.

Title: Re: PE400 Flywheel Puller
Post by: lukeb1961 on March 05, 2011, 01:17:02 pm

there are a few little tools that will make your life immensely easier.
See here for a selection of homemade whatsits:
http://cid-407d7ef0965d3991.office.live.com/browse.aspx/Pure%20Enduro/tools