OzVMX Forum
Marketplace => Wanted => Topic started by: Freakshow on February 07, 2011, 08:05:15 pm
-
as above
-
Replica plain plastic base - no mounts $ 66.00
Replica plastic base with mounts fitted $ 110.00 (as pictured)
(http://i15.photobucket.com/albums/a393/gmcloa/products/HL-seat-base-under.jpg)
-
as in plastic plastic or fiber glass ? i have seat base with shitty foam but the last 10cm has been cut from the front. it has the rear mounts, and i can probbly fab the front one. are the seats normally stapled or metal teeth hooked on ?
-
These bases are made from plastic plastic.
Original bases are made from plastic plastic also.
Not sure but I think the covers are stapled on.
-
thats cheap buy it freaky :o
-
hey geoff, while your on a roll. can you post up the 125A chamber/pipe and filter-airbox you make ?
cheers
-
(http://i15.photobucket.com/albums/a393/gmcloa/Pipes/74YZ125A-pipe-1.jpg)
(http://i15.photobucket.com/albums/a393/gmcloa/Pipes/YZ125A-aibox-.jpg)
-
Stop being a tightarse Kerry....buy the lot.....for christs sake...it ill keep him off the forum for a couple a days ;D
-
Freaky that pipe aiibox combo will be the best money you can ever spend on a YZ 125A ;)
Or is that a 250 front end and decent shocks ???
-
id like to but i have had some real bum deals lately, that set me back, so im im short of that sort of cash, so im living in hope. pipe might be a goer in the short term though, depending on price.
-
Pipe is $418.00
Muffler is $209.00
Pipe and muffler is $600.00
Airbox is $286.00 plus filter and cage
Postage $22.00
I have had some real bum deals lately too, that have set me back, so I'm short of cash too, so im living in hope the pipe might be a goer in the short term
-
Geoff you jigged for that pipe or you need a frame ?
whats the dia at the muffler end ? i have a few can around here and some old HPF stuff that might fit....
-
Freaky, you just bolt it on and go.
-
Geoff you jigged for that pipe or you need a frame ?
whats the dia at the muffler end ? i have a few can around here and some old HPF stuff that might fit....
im prity keen at that money
All pipes and mufflers on my price list are jigged for.
The stinger tube is 1" - 25.4mm OD
Any muffler with a similar core size will do, muffler body should be around 200mm long
-
Pipe is $418.00
I have had some real bum deals lately too, that have set me back, so I'm short of cash too, so im living in hope the pipe might be a goer in the short term
OK go on, make me a pipe then, cant have you not eating can we......
-
Freaky, you just bolt it on and go.
Davey was this pipe jigged from your shitbox ? if so why arent you using the middle rubber mount under the seat ?
-
You dont need to as the muffler has a big mount on it.....dont tell me you've been a tightarse again and not bought the muffler?....howd the brake pedal bush go?
-
Bush no problem wen in your you finger in a bum. FOrked the swing arm bush so had to go though my stash and fin another, only to find once assembled the Early DT1 frame ( with the KEy) uses a front brake arm that differant to the Dt250 style round arm. so now i have to sort out that and make somethign up to suit.
Tool worked a treat as did the Silver bullet unit.
Pipe turned up yesterday some things id like to see differant , but cant comment till its on the bike, which means i have to fit the motor and im not quite there yet.
propally should have looked closer and asked to see your 125's pictures first though i thinks though, happy to discuss offline with you.
HEy you near the airport on Tuesday ? i can meet you in the no stopping zone and hand you that tool and a front tyre for the stewman choo - ( get your bolts too)
-
Still need a YZ125 stator hence the motor not in yet.................
-
better than stock ;)
http://cgi.ebay.com.au/1974-1975-Yamaha-YZ-MX-125-175-PVL-Digital-Ignition-CDI-/110660808805?pt=Motorcycles_Parts_Accessories&hash=item19c3e5f065
-
Apparently hes still hurting from GMC's greatest ever sale......selling a new pipe to Freaky.
-
YEr thanks vandy, but sussed out that one before, he took it off his old MX racer.
I have the part numbers for it and im keeping my out for the rotor and bottom plate as i have the PVl stator etc here to make one up ( plus another $300 for one would kill me)
Other option is to hopefully fall over a yZA one in the mean time, if im really pushed i think i have an mx125 or points one here somewhere i can knock up, but thats a last resort.
Unfortunalty this YZ burnt my fingures a bit and im having to spend money rebuilding it and fixing up someones else fork ups, which i didnt see coming. :-[
-
yer.... not like me huh. But you sucked me in Davey, Although you and me will have words if the output isnt there, but lets wait and see when i got the motor back in it and its all strapped in. I actually have a few mods for you to on the flip side of this you might be interested in too.
-
Apparently hes still hurting from GMC's greatest ever sale......selling a new pipe to Freaky.
Not anymore.
He’s now having a panic attack about drilling a hole in the frame to support the different pipe ;D