OzVMX Forum

Marque Remarks => Yamaha => Topic started by: ji107 on November 23, 2009, 04:19:09 pm

Title: DT1 cylinder head
Post by: ji107 on November 23, 2009, 04:19:09 pm

Does anyony know if there were DT1/2 cylinder heads available without the cut off fins on the RH side,to clear the pipe?
If they were available does anyone know where I can get one?
Thanks
J I

Title: Re: DT1 cylinder head
Post by: mx250 on November 23, 2009, 04:50:41 pm

Not to my knowledge.

If you wanted fins for a particular project you could cut them off a spare head and weld them on ;). I've seen repaired fins and you would be hard placed to pick 'em 8).

Title: Re: DT1 cylinder head
Post by: ji107 on November 23, 2009, 04:56:22 pm

I may have to go that way, but would prefer not to.
How about RT1 head?

Title: Re: DT1 cylinder head
Post by: mx250 on November 23, 2009, 05:42:39 pm

Quote from: ji107 on November 23, 2009, 04:56:22 pm

I may have to go that way, but would prefer not to.
How about RT1 head?

Ditto.

Title: Re: DT1 cylinder head
Post by: firko on November 23, 2009, 07:59:34 pm

DT2MX from memory. But I'm probably wrong. :-[

Title: Re: DT1 cylinder head
Post by: Freakshow on November 23, 2009, 09:15:35 pm

You mean all same height or only the very end ones ? 

I have Dt1 heads that have both end fins same heights but are slightly lower in the center, 2 plugs also and run inline with the frame not at right angle like the normal DT1 heads you see.  I think the casting is 214 but id have to look, sorry no foto here, down at other place.

other similar options are YZa(http://i33.photobucket.com/albums/d88/munchboxlive/yz003.jpg)
or DT2mx   (http://i33.photobucket.com/albums/d88/munchboxlive/RIMG0392.jpg)

Title: Re: DT1 cylinder head
Post by: ji107 on November 23, 2009, 10:48:57 pm

Yes, like the one in the photo (no52), or similar

Title: Re: DT1 cylinder head
Post by: Freakshow on November 24, 2009, 11:25:37 pm

http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=180433216758&viewitem=&sspagename=STRK%3AMEWAX%3AIT

http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=110457345113&viewitem=&sspagename=STRK%3AMEWAX%3AIT

Title: Re: DT1 cylinder head
Post by: Freakshow on November 30, 2009, 12:08:03 am

Here is a webco i have, same all the way across.
(http://i33.photobucket.com/albums/d88/munchboxlive/RIMG0545.jpg)

This one not sure, its off the YZ but its sand cast so im not sure someone might be able to ID it???  The square sections seem to be part of it as there equal levels and not cut with a grinder or similar. I have no idea what it is, what does the ACK look like ?  anyone(http://i33.photobucket.com/albums/d88/munchboxlive/RIMG0530-1.jpg)
also while on the subject them red alloy Bolts are they able to be torqued up to the same Lbs as the steel ones or safer to leave them a bit on the soft side ?