Author Topic: 1984 CR500 rear hub  (Read 606 times)

0 Members and 1 Guest are viewing this topic.

Offline ralph311

  • C-Grade
  • **
  • Posts: 78
    • View Profile
1984 CR500 rear hub
« on: November 14, 2018, 12:19:08 AM »
Anyone know if a 1984 CR125 rear hub will fit a 1984 CR500?

Thanks.

Offline enzo906

  • C-Grade
  • **
  • Posts: 73
    • View Profile
Re: 1984 CR500 rear hub
« Reply #1 on: September 05, 2019, 03:36:55 PM »
apparently?
I need one too

Offline Hoony

  • Legend
  • *****
  • Posts: 4207
  • Melbourne, Vic.
    • View Profile
Re: 1984 CR500 rear hub
« Reply #2 on: September 07, 2019, 01:49:38 PM »
general rule for Honda's in that era is yes.
Long time Honda Fan, but all bike nut in general, Big Bore 2 stroke fan.    http://www.youtube.com/watch?v=XJoKP6MawYI
1985 Honda CR500RF "Big Red"
1986 Honda CR250RG
2005 KTM 300EXC "The GruntMeister" ( I love that engine)

Offline Momus

  • Legend
  • *****
  • Posts: 576
    • View Profile
Re: 1984 CR500 rear hub
« Reply #3 on: September 07, 2019, 10:09:50 PM »
250 hubs will interchange but I believe the 125 units are different. Do confirm that.
« Last Edit: September 07, 2019, 10:15:43 PM by Momus »

Offline enzo906

  • C-Grade
  • **
  • Posts: 73
    • View Profile
Re: 1984 CR500 rear hub
« Reply #4 on: September 11, 2019, 11:14:16 AM »
same part number for 125 250 500 for 84 and 85 and 86 so they must all be the same
then again part numbers sometimes can be misleading (XL600 tappet adjuster screws had one number but 2 diameter threads?????)

Offline ralph311

  • C-Grade
  • **
  • Posts: 78
    • View Profile
Re: 1984 CR500 rear hub
« Reply #5 on: September 26, 2019, 05:19:47 PM »
FWIW the 125 hub does fit in a 500 but it's not the same. The offset is different, I had to make new spacers to get the chain to line up.

Offline Hoony

  • Legend
  • *****
  • Posts: 4207
  • Melbourne, Vic.
    • View Profile
Re: 1984 CR500 rear hub
« Reply #6 on: September 28, 2019, 08:45:15 AM »
same part number for 125 250 500 for 84 and 85 and 86 so they must all be the same
then again part numbers sometimes can be misleading (XL600 tappet adjuster screws had one number but 2 diameter threads?????)

for CR500 85 & 86 rear hubs are different, 85' has a single bearing on drive side where as 86' has 2. i believe they are both interchangeable for either bike dimension wise
Long time Honda Fan, but all bike nut in general, Big Bore 2 stroke fan.    http://www.youtube.com/watch?v=XJoKP6MawYI
1985 Honda CR500RF "Big Red"
1986 Honda CR250RG
2005 KTM 300EXC "The GruntMeister" ( I love that engine)