Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - TT5 Matt

Pages: 1 ... 6 7 [8]
106
For Sale / yz250j swingarm and linkages
« on: February 13, 2009, 04:01:58 AM »
anyone need a yz250j swingarm or linkages pm me for a price


TT5 Matt

107
For Sale / yz250g parts 3r4
« on: February 13, 2009, 03:56:40 AM »
got some yz250g 3r4 bits
frame
airbox minus cover
gearbox
clutch
maggie
weathered bare seat base
foot pegs and brake lever
shock
swingarm
cases [weathered crank case area]

pm me for a price


TT5 Matt

108
For Sale / PE250B TANK
« on: December 19, 2008, 12:34:24 AM »
hi all
the tank has got a long knee/leg ding on the r/hand side not to deep which would blow out or panel beat out though the filler   other than that its straight and got good thread on the filler and tap spigot $150 plus post


TT5 Matt

109
Other Makes (CanAms, Coopers, etc) / WOW OUR OWN PAGE!!
« on: July 07, 2008, 10:21:25 PM »
hi all
i was wondering which page i could post questions on for my new aquired cooper mxer i bought off Freaky. many thanks to the site owner

TT5 Matt

110
Honda / 81 cr250 b forks
« on: May 01, 2008, 03:27:24 AM »
hi all
got a cheap ioose cr250  81 model[that what its marked as] front end off the wreckers and wondering if 43mm forks drum brake/bottom compression dampening screws /air caps were about back then? what travel are they and fork oil capacity/level are they? does any one know?

TT5 Matt

111
Suzuki / ts 250/185a carb specs
« on: April 19, 2008, 12:49:47 AM »
hi all
has any one got float levels/carb specs on the twin cable ts250/185a carbs?
a old mate gave me a tray full of 185 and 250 carbs and other useable spares and i like to try a 250 carb on my rm185 project to get a bit more poke from the doscile little motor, the a model 185 doesnt seem to have much of a chance to fit a bigger carb than 28mm because of the spigot intake on the barrel is there any way this can be changed to open up the intake port like the rms125?

TT5 Matt

112
Suzuki / ts250a fork oil capacity
« on: April 13, 2008, 03:36:20 AM »
hi all
how many mls of fork oil for my ts250a?

TT5 Matt

113
Wanted / rms 125 l/hand s/cover and front and rear guards
« on: April 11, 2008, 11:28:24 PM »
hi all
any got a left hand sidecover and front and rear guards for a rm125m or s in good condition?and a s pipe or two

114
Suzuki / RMS 185A HOP UP
« on: March 17, 2008, 08:42:48 PM »
hi all
got given a going  ts185 and 250 both a models and a week after buying a rms125 frame off ebay i thought why not a rms185 for a neat little trailie to buzz around the hundereds of 2 wheel tracks starting from the outshirts of town and going hundereds of kms in all directions,
want i would like to know is whats the biggest carb you can fit to the standard inlet rubber without it splitting[im thinking 28mm ts 250a carb] and open out the inlet port ,squeze up the mixture with a head surface on the lathe and clean up the transfers and exhaust ports,does anyone got a design for a pipe to suit the rms chassis with a 185 or will a cr125 pipe fit?

thanks TT5 Matt

115
Wanted / RMS 125 DOWN PIPE
« on: March 01, 2008, 03:29:07 AM »
hi all
just got a frame swingarm and motor with electrics  to match the tank ive got and am chasing a gen s model pipe pm me if you have one for sale


TT5 Matt

116
For Sale / rm 80 78 0n cdi unit
« on: February 15, 2008, 10:40:39 PM »
good wiring loom plugs and rubber mounts $60 plus post  0488704589


TT5 Matt

117
For Sale / xl250rh cdi
« on: February 15, 2008, 10:30:39 PM »
removed from a running bike i wrecked years ago $60 plus post  0488704589

118
For Sale / yz 400d cdi with holding pouch
« on: February 15, 2008, 10:26:06 PM »
i took this off my tt500 30 years ago because of a cracked stator plate and have no use for it $90 plus post 0488704589


TT5 Matt

119
For Sale / rms 125 tank
« on: February 15, 2008, 10:20:43 PM »
tank is straight with 2 shallow dents,it might even polish up ok $200 plus post 0488704589


TT5 Matt

120
For Sale / yz 125 b tank
« on: February 10, 2008, 09:18:24 PM »
hi all
my first post on this great site!!! ive got a yz125b strap  tank for sale i bought it for a hl but when compered to the c model theres no cutout for the oil filler so out it goes.  its got a few small dings on the sides [5] and where the head stem pivets in front of the tank filler and the top is straight.  email me or phone 0488704589


tt5 matt

Pages: 1 ... 6 7 [8]