Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Iain Cameron

Pages: [1] 2 3 ... 132
1
Suzuki / Re: Rm125b forks
« on: May 22, 2019, 11:04:59 PM »
Oh no here comes 30 pages plus .  sorry Craig couldn't resist it .

2
General Discussion / Re: OZVMX - History / What year did it start ?
« on: May 11, 2019, 02:17:32 PM »
I liked the stories with photos of a pile of rust being rebuilt and brought back to life . Firko did it as well . there was some great resto jobs on here . some good "How To " posts too .

3
General Discussion / Re: OZVMX - History / What year did it start ?
« on: May 08, 2019, 10:37:55 PM »
I think a lot left when some of the posts got quite nasty . Graeme was quite a good mod and didn't put up with it . I miss some of the older blokes mmmm . I pop in every once in a while but not lie b4 .  Iain used to be Iainyz a long time ago .

4
General Discussion / Re: 2019 Broadford Bonanza
« on: April 17, 2019, 08:58:47 AM »
Also the Dirt bike swap meet down by the entrance gate   Im bringing lots of early Yamaha stuff . also looking for a 74/74 MX YZ  125 Yamaha .

5
Tech Talk / Re: Hmmm looking for more top-end. Piston Port 250.
« on: April 10, 2019, 07:36:48 PM »
I will bring a few copies to Broadford .

6
Tech Talk / Re: Hmmm looking for more top-end. Piston Port 250.
« on: April 09, 2019, 08:33:03 PM »
I have the Yamaha tuning hop up manual for stages 1 , 2 , and 3  for the 250 . stage three is road race or US flatrack . all porting and numbers I will bring a copy to Broadford Johnny .

7
Tech Talk / Re: Hmmm looking for more top-end. Piston Port 250.
« on: April 08, 2019, 10:01:28 PM »
First of all piss of that huge flywheel and points . I use a 77 YZ 250 CDI system  with a internal flywheel it will rev and pick up quicker .

8
Wanted / Re: 36 mm forks to suit IT400E
« on: April 08, 2019, 08:19:44 PM »
Bringing some over to Broadford at easter Tony .

9
Wanted / Re: WANTED - Yam DT2/3, RT2/3, RH crankcase.
« on: April 08, 2019, 08:18:19 PM »
Ok tank yes , exhaust spigot yes , eng mount bolts yes , rubber tank stays yes , wheels rear with tyre as well yes , front ok full width hub or conical ? . cover front sprocket yes . Bars no . clutch and brake levers I will have to look . cases second hand both 250 and 360 .
 DT2mx right eng case .
 

right every thing except the bars .
  Done packed on its way to broadford

10
Wanted / Re: WANTED - Yam DT2/3, RT2/3, RH crankcase.
« on: April 07, 2019, 02:33:22 AM »
So are we after a left or right side case 250 or 360 . Ive got NOS 250 clutch side .

11
Wanted / Re: WANTED - Yam DT2/3, RT2/3, RH crankcase.
« on: April 05, 2019, 06:08:54 PM »
Im bringing 2 or 3 to Broadford John . the DT and RT are not the same .

12
Yamaha / Re: Motocross seat conversion for Yam DT1?
« on: February 19, 2019, 09:44:43 PM »
Ive used a DT2MX seat on one and the other a TM125 Suzuki seat the DT2MX one I had to take a bit (3/4 inch out of the rear loop and press the rails together and reweld .

13
Bike Transport / Re: Tassie or Melbourne to Bowral or Mittagong
« on: January 19, 2019, 01:36:04 PM »
Covered thanks any way gents .

14
General Discussion / Re: Plastic Guard suppliers
« on: January 19, 2019, 01:34:09 PM »
John Tate in Qld is a Preston Petty agent .
or was a Cpl of years ago John are you still an agent ?

15
Wanted / Re: WANTED - Yam DT250, DT400 triple clamps.
« on: January 15, 2019, 09:10:17 PM »
Sent you a Cpl of photos John .
on Face sook .

Pages: [1] 2 3 ... 132