Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - matcho mick

Pages: [1] 2 3 ... 147
1
Tech Talk / Re: Fork leg straightening
« on: January 12, 2018, 09:45:48 PM »
Lightfoot Engineering??,down there somewhere?? :P

2
geezas,pretty serious numbers there,apart from i don't know what a 2F1 needle is,& 30 pilot sounds tad lean,even for reed valved bully,109 nj's up there bigtime?, :P

3
For Sale / Re: 82 XL500 forks
« on: December 27, 2017, 12:06:51 PM »
Hey don’t suppose you still have these?
2015,for $35,there's supreme optism right there  ;D, :P

4
Introductions / Re: New member michael
« on: December 27, 2017, 12:02:44 PM »
welcome aboard michael (need more micks 8)),you will be in good company ,most of the KTm guys cant spell for shit anyway,few TT/Xt guys here too,cheers mick :P

5
General Discussion / Re: Ripped off on Gumtree
« on: December 22, 2017, 11:47:50 AM »
maybe a 3rd party scam??, false gumtree page??,justa thought,good luck with it mate, :P

6
Wanted / Re: road gear for tt/xt500
« on: December 22, 2017, 11:45:03 AM »
only the headlight and the tt500

speaking in riddles again Jimbo  :), :P

7
Wanted / Re: Honda XL250s Rocker box
« on: December 21, 2017, 09:53:40 AM »
ah twin exhaust port XL,yeah shrouded recessed dowell pins are a bastard to get at purchasewise,tip, really big vice grips & effing lots of heat for them,M de  be drilling  exhaust pin access hole for awhile mate,directly over the integral head mount lug,(lots of swarf generated there LOL) suck it up Curtis  ;), :P

8
Wanted / Re: Honda XL250s Rocker box
« on: December 20, 2017, 11:08:51 AM »
bit unusual Curtis,are the spindles rotating in the cover?,(or rockers seized to them),maybe a fair bit of oven heat allover,then jar the cover on a block of wood see if that moves them outwards enough to grip them?? :P
ps what year??

9
General Discussion / Re: Funnies/Jokes
« on: December 08, 2017, 12:39:12 PM »
finally an embarrassed husband goes to his doctor,tells his doctor he's having trouble getting an erection,& it's causing problems with his wife
the doctor checks his blood pressure,& other vitals,all seemed fine,after a thorough examination,doc asks to see his wife
when she arrived,doc places her in another cubicle,then asks her to disrobe,then asks her to rotate slowly,then raise her hands above her head & rotate slowly again,then he asks her to touch her toes,& cough,having finished his examination,he then asks her to dress,leaving her he goes back to the waiting husband in the other cubicle,
you can relax now,theres absolutely nothing wrong with you,i couldn't get an erection either!!

10
Yamaha / Re: Dimensions of yokes for Yamahas with 36mm forks...?
« on: November 30, 2017, 05:30:23 PM »
The 60mm offset ones are from the inline axle forks. The leading axle TT/XT500 clamps will have  a lot less offset than 60mm.
[/quote
onya LW,set me another task  ;),your'e correct,leading axle top trees 20mm offset, JP, the h/bars are angled back on fixed risers,with just enough fork clearance, :P

11
Yamaha / Re: Dimensions of yokes for Yamahas with 36mm forks...?
« on: November 29, 2017, 11:26:52 AM »
forks are 36 in the trees!,centres 185,offsets 60,stems 25,(but bottom bearing surface is 30 dia),overall length is 230,it's removeable from lowers,(pressed?,& clamped), :P

12
Yamaha / Re: Dimensions of yokes for Yamahas with 36mm forks...?
« on: November 28, 2017, 06:33:54 PM »
just ran a ruler across XT/TT front end,the 36 forks will clear the h/bar clamps,just!,about 2mm innit,these are the "stepped" forks,(reduced between the triples), :P

13
For Sale / Re: 1980 Can Am MX6 250
« on: November 23, 2017, 09:39:48 PM »
pretty sure having green plates with white numbers is a no brainer  :o, :P

14
Tech Talk / Re: dt or it175 cylinder sleeves?
« on: November 05, 2017, 11:39:53 PM »
my P3 MV 2fiddy with hi comp kwaka Z pistons  8), :P

15
Tech Talk / Re: dt or it175 cylinder sleeves?
« on: November 05, 2017, 10:55:11 PM »
$180 fking cheap option  :o,ok admittedly a one off, i bought an excess11 block for $50 from local wrecker,hacksawed in 1/2 to fit in shed stove,bingo 4 X 72mm bore sleeves (with flanges),look around,even wet sleeves from fergy tractors do pommy singles,(after external machining) there was a firm in tamworth doing spun cast iron sleeves (years ago  ::)), :P

Pages: [1] 2 3 ... 147