Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Topics - MX?

Pages: [1] 2 3 ... 7
Wanted / '74 XL350 parts wanted
« on: January 23, 2018, 09:51:36 PM »
Anyone sitting on a box of street gear for the above?  ;D
Looking for a bunch of stuff to put one back on the road.

Wanted / XL175 kickstart spindle
« on: October 28, 2017, 12:48:25 PM »
Any chance someone may have one of these laying about collecting dust?  ;)
For the early models.

General Discussion / Brake light switch
« on: January 11, 2017, 07:16:22 PM »
Anyone know where to get a switch like this? Spring pull unit
Preferably at a price I won't need to sell a kidney for  :D

Wanted / Need a '70's Honda seat lock frame part?
« on: November 09, 2016, 09:59:57 PM »
Anyone have an old worn out frame they'd like to cut up?  ;D
I'm looking for the frame section of a seat lock mounting plate.
I think most of this era bikes had the same set up.
Will get some pics of what I'm after shortly.

Manuals & Technical Doco / KX125 Manual 1985
« on: August 20, 2016, 02:31:52 PM »
Anyone interested in this?
Ratty outside, finger prints and dog ears inside but good enough to use

General Discussion / Any Hodaka owners here?
« on: July 08, 2016, 11:34:13 AM »
Hi all, just picked up a '73 Dirt Squirt.  :o
Anyone know if they can be road registered?
Bit of polishing to do first though.  ;D

Bike Transport / Tassie to Melbourne area?
« on: May 11, 2016, 05:49:13 PM »
Any ideas on getting a bare frame between these two?

General Discussion / Alloy tank builders?
« on: July 06, 2015, 09:25:13 AM »
Any in Australia?
Othwise does anyone have a recommendation.

Honda / Looking for switch - XL 250K1 I think
« on: June 27, 2015, 05:53:09 PM »
Anyone have either a complete switch or the guts there of?
Pretty sure this was off the XL250 Motosport

For Sale / Kawasaki KLR250 Parts
« on: June 02, 2015, 04:47:21 PM »
I have an old KLR250....2/88 build.
Will be selling parts from this if anyone's interested.  :)
Don't know the condition of the motor other than it turns over OK.

Wanted / XL250S 1978 R/H handlebar switch
« on: May 23, 2015, 05:45:59 PM »
Fella in the UK looking for one of these, if anyone can help him?
Original post here....

Yamaha / DT 400 Speedo wanted
« on: November 09, 2014, 09:55:35 PM »
Have a mate who's bought a nice '77 DT400. He's looking for a good speedo for it.

Yamaha / Anyone have info on this bike?
« on: August 17, 2014, 09:13:43 AM »
Posted on FB...
Is it a mod or standard Yammie?

Tech Talk / Parts Washer solvent question
« on: August 02, 2014, 09:14:59 AM »
So I've gone and bought a small parts washer from Repco, I'm sure I read a post here ages ago about using kero as the solvent? but can't seem to find it now.
Actual approved solvent is "Water /Household detergent" but I doubt that's going to clean much.
What does the panel say?

Tech Talk / Shop that can re-build a honda CB450 twin crank?
« on: July 07, 2014, 09:52:33 PM »
Anyone know of such a miraculous place?
I think I'll need to try and get mine done as the rods are frozen and the whole thing will need refurbishment, otherwise it's pot luck with another used one or $5k for a NOS unit...(that's not going to happen me thinks)
These cranks are all pressed together and don't have a pin through the big end of the conrod, our local engine engineering shop doesn't want to know about it.
I'd imagine if it can be done it'll need the journals maybe welded up and re-ground, as they will probably be rust damaged.
Any ideas out there?

Pages: [1] 2 3 ... 7