Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - micko

Pages: [1] 2 3 4
1
Wanted / yz250a swingarm collars wanted
« on: July 17, 2019, 06:45:06 PM »
Hi Guys,
looking for swingarm collars, can be s/hand prefer new genuine #90387-16449-00 to run Kerry marsh's bearing set up.
Maybe even genuine bearings #93321-22001-00 if theres any laying around :)
thanks

2
Tech Talk / Thor swingarm
« on: March 25, 2019, 05:50:22 PM »
hi Guys,
Is there any way of id-ing a Thor arm ?

3
Wanted / yz/dt clutch actuator replacement
« on: July 25, 2018, 05:42:20 PM »
I have a cracked nylon/plastic bush worm drive thingy inside the actuator arm, Iain mentioned someone here has made bronze replacement ones. Anyone know who it is ?
cheers.

4
Tech Talk / Front end conversion RM125A
« on: June 08, 2018, 08:00:58 PM »
Bit confused, fitted my 250A front end into the 125A today, I want to use the 36mm forks - and read an article about it being a straight bolt on swap over they did back then - now the fork legs hit on the tank ???? any suggestions ? The 250A and 125B part # is the same for the bottom triple tree. 
Help appreciated

5
Wanted / RM125B forks Wanted
« on: May 01, 2018, 03:30:16 PM »
and triple clamps - worth a try, must be good nick

6
Wanted / RM370 Kick start shaft
« on: April 08, 2018, 08:42:51 PM »
Wanted for a friend, 77 RM370B kick shaft. The coarse spline one, part #26211-41201
Thanks.

7
Wanted / 38mm mikuni carb wanted
« on: February 27, 2018, 11:22:34 PM »
Looking for a s/hand mikuni vm38 carb if anyone has one laying around.

8
Manuals & Technical Doco / Wanted 1974 YZ250A workshop manual
« on: February 26, 2018, 04:25:57 PM »
cheers in advance :) 

9
General Discussion / YZ125X
« on: January 11, 2018, 12:47:23 PM »
Got a mate looking at a 1976 YZ125X (air fork model) , very original condition, been sitting for many years.
Question: Were they yellow in oz and what do you think there worth these days (comes with a brand new cylinder in a box)
Cheers

10
Tech Talk / Rear hub difference RM250A/B/C
« on: May 03, 2017, 09:44:58 PM »
Apart from bearing sizes is there a difference, are they all magnesium ?

11
Tech Talk / Confused -YZ250A crank ROD
« on: January 03, 2017, 08:30:36 PM »
Am i correct ?
original part # 431-11651-00-00 as per prefix on frame and engine,  superseded to 311-11651-00-00  DT Model ?
I believe there 125mm long.Not to be confused with the 360 that is 130mm long. Yamaha part list is very confusing.
Can someone enlighten me, and steer me in the right direction with a replacement.
cheers 

12
Wanted / Wanted - 1977 Yamaha YZ125D
« on: January 03, 2017, 07:37:40 PM »
Posting for a fellow enthusiast, he's looking for a 1977 Yamaha YZ125D in reasonable condition and running.
let me know whats around and i will pass on his contact details. He is in Perth.
Cheers
Micko

13
Bike Talk / YZ250A Pistons
« on: July 29, 2016, 11:08:46 PM »
The YZ is starting to get abit rattly in the top end, haven't had a look yet but are Pistons easy to come by ?

14
Wanted / 74 YZ250A crank seals wanted
« on: June 14, 2016, 04:50:40 PM »
before I go searching, does anyone know a source for these ?

15
Wanted / Wanted-78/79 CR250R
« on: April 19, 2016, 06:44:41 PM »
Hi guys,
Posting on behalf of a mate, looking for a 78/79 mdl Honda CR250R. Doesn't want a show bike just something to jump on and race, let me know what you have and I will pass on his details.
Cheers

Pages: [1] 2 3 4