Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - ELC hunter

Pages: [1] 2 3 ... 7
1
Wanted / Early TT600 rod bearing and crank pin wanted
« on: April 03, 2025, 10:38:34 am »
Hi all would anyone know off an aussie dealer or a person that might have these parts on the shelf after rod bearing pn.93310-634K2,Rod Pin 34K-11681-00 and thrust washers 90209-34254 for an 1987 TT600.Reading there is 3 sizes for this thing as the model progressed through it life,but the parts i need are for early type.Nothing shows up on dealer access for old stock when from my yam shop.Prefer to buy au but see what might come cheers Gavin.

2
General Discussion / Testing yz465 ignition system who to send to?
« on: March 04, 2024, 12:27:15 pm »
Hi is there anyone who can bench test a complete ignition system,I thought there was someone in SA but have forgoten who that was. A mate has a yz465 which is fitted with a vape system internal rotor flywheel and he would like test the orignal system if good wants to run external flywheel and parts as a standard system.

3
General Discussion / Yamaha IT forum not working anybody have any details.
« on: February 19, 2024, 05:33:27 pm »
Hi any one know why the IT forum won,t work when I try to open it ,displays a message suspended is this for any particular reason  cheers ELC.

4
Have a wr360 1993 bike with a stuffed barrel im doing for a mate which is stuffed coating wise but there is a few score marks 1mm deep over a small area, are the shops able to plate this kind of damage succesfully or chase a better cond barrel and replate.Any ideas on rod kit brands to use for same bike cheers,mate is keen after attending cd16 to get it going again.

5
Wanted / TT XT600 top end wanted .
« on: August 29, 2023, 12:36:50 pm »
Hi working on mates bike which has starved it self of oil,previous owner rebuilt after oil starved oirignal parts died then new parts died same death within low klms.Have found the issue counter shaft welsh plug failed lost oil pressure to top end the last owner fitted 98mm liner Arias high top piston etc now scrap.Mate is undecided on what he want to do regards rebuild has any one got a
 usable barrel piston for xt or tt for sale or contacts of good parts supplier  in Au .Barrel is single bolt type 53x .cheers ELC hunter.

6
Wanted / Wanted wrk250/60 parts
« on: May 04, 2022, 09:43:55 am »
Hi would anyone have a parts bike or any left over bits from a resto on a wrk husky a fellow vmxer is trying to get one ready for the next cd when ever that happens cheers ELC hunter

7
Wanted / wanted tt250 89 carb kit or carb where to source
« on: February 02, 2022, 08:50:18 am »
Hi does anyone have or know of a supplier for overhaul kits for TT250 teiki carbs twin cam models 85-93 or possibly a new replacement can,t seem to find much on them any where cheers ELC hunter

8
General Discussion / Paddock bike starter any recommended
« on: May 14, 2021, 07:41:50 am »
Looking at a bike paddock starter any recommended to be used for 500 two stroke huskies cheers gav

9
General Discussion / xr500 re electrical testing specs wanted.
« on: May 03, 2021, 03:21:16 pm »
Hi  anyone know the test values for 83/84 xr500 for stator, coil, and that transducer on the right side thanks the bike has thrown a chain and cut the wiring even after repair no spark cheers ELC hunter.

10
General Discussion / 89 tt250 carb repair
« on: April 17, 2021, 08:12:00 pm »
Hi has anyone know of a supplier for an carby overhaul kit which includes vacuum diaphragm for the TT250 89 model twin carbs cheers ELC hunter

11
General Discussion / Husky motoplat flywheel thread size for puller.
« on: February 15, 2021, 02:59:20 pm »
Hi all what size is the internal thread on early 72 husky motoplat fly wheel ,trying to swap stator to one that works and am unsure of thread size and pitch cheers.

12
Wanted / Ktm380 parts
« on: May 10, 2020, 07:28:12 pm »
Hi all would anyone have any parts for a 2000 380 that would be for sale or leads on good parts supplier mainly engine parts it’s son law project cheers elc hunter

13
Wanted / Husky 84 kick start lever straight type.
« on: October 28, 2019, 12:45:00 pm »
Hi after a straight shaft kick start lever for wr500 xc 1984ish etc. don't know what other models they might fit but it is needed so starting is easier then with that bent kick lever cheers ELC.

14
General Discussion / husq wr500 vs xc500 1983/4 main differences.
« on: July 23, 2019, 10:58:10 am »
Can anyone describe main differences between 1983 xc500 to 1984 wr500 so to be able to identify if looking at the real thing before purchasing. Running gear engine suspension looks similar.   Any issues if one is US import wr500 doesn't have compliance plate so im thinking it to be a import ? It was at cd15 for sale. Frame number is stamped neatly with Husqvarna 1then a more roughly stamped number which equals 84 wr500 id is this sort of stamping common like this on these? cheers ELC hunter.

15
Wanted / cr80 1983 nos inlet manifold (insulator)
« on: June 19, 2019, 02:27:51 pm »
An one know where to obtain a inlet manifold for cr80 1983 pn 16211 GC4 700 got one from the states but angled to right side not left as needed cheers.

Pages: [1] 2 3 ... 7